Digiprog 3 clone questions and answers

[Nicolas9]

I need help with a 09 Nissan gtr. Can I change millage with my digiprog clone and does anyone have the location of the eprom chip? Thanks in advance I mainly just do Chevrolet trucks

solder wires on the back. easy

[alclot]

Hi mates,
I have valeo bsi with 95160 which I would like change km and clone dump in donor one but with upa doesn't write well by pinout on board. Can I do that well with digiprog?
Car is a Peugeot 307.
Thanks in advance

[mikkhh]

valeo bsi works ok with digiprog, use adapter 47

[honingkoning]

Hi mates,
I have valeo bsi with 95160 which I would like change km and clone dump in donor one but with upa doesn't write well by pinout on board. Can I do that well with digiprog?
Car is a Peugeot 307.
Thanks in advance

Or set upa to 3.3 V and Will be ok.

[alclot]

I did that and it reads ok but read after write dump doesn't change. The original dump I modifiqued by nyo 4.0.
Do you know how to do it well?
Thanks

Or set upa to 3.3 V and Will be ok.

[rtbdiagnostic]

Howzit need advice please on 2011 VW Golf6 1.4 TSI did not know if it was MM or VDO cluster - used digiprog dash diagnostic until 2012 read 100% 234000km write 228000 needed 158000 dash went black and restarted tried a few times like it reads 158000 although dash shows 228000km then i write again to 155000 stays on 228000 it shows - car starts drives adds mileage on tripmeter etc. some funny sign displaying when driving looks like a speed control sign
Any suggestions will be appreciated

[rtbdiagnostic]

Today I try golf 6 with dash mm9rm10 read good mileage(174000) and decided to go for write put 164000 but the dash jump at 172000(car start),disconnected battery no change,read mileage again digi read 164000 but dash show 172000 drive 3km read again and digi read 172003. Any value I put dash jump at 172000.

ever found solution for this dash with digiprog ?

[sendreq]

It won't go with digiprog. I did this type of dash (MM7) with X-tool.

[bersch8688]

Digiprog 4.94
VW UP 2013 ---> OBD Work 2min.

[Berubeg]

Someone try bmw 330 xi 2006 with digiprog? I have the car in menu but i’m afraid to try bmw with digiprog

[teerak2uk]

Someone try bmw 330 xi 2006 with digiprog? I have the car in menu but i’m afraid to try bmw with digiprog

Use r260 for CAS and r270 for dash

[Music73]

Someone try bmw 330 xi 2006 with digiprog? I have the car in menu but i’m afraid to try bmw with digiprog

You can’t do these via obd..

You need to remove cluster, read and save 35080 and either replace with new or try to reset with r270( as Terra mentioned).. then rewrite saved data with new valve..

The cas I use r260 but I have been told that the r270 can do the cas aswell but I prefer the 260 it seems more stable..

I haven’t tried using digi to do the cas as I don’t trust it but it may possibly do it if you haven’t got the above tools but worth the investment if your gonna to do more


Sent from my iPhone using Tapatalk Pro

[rtbdiagnostic]

There are 2 types of MM dash in golf6
MM5 & MM7
One of them is NEC + 95320. Digi won't work here.

can digiprog version 4.94 do this golf 6 nec 95320 dash in any possible way

[rtbdiagnostic]

can it be done by opening up cluster in any other way than obd maybe nec 95320

[Alexxelax]

Hi all.

I need help with Volvo v70 2005, i have solderd and colour code converted adapter 51 and also tried with 48, i get "INIT ERROR", i have check and re-checked connections but cant find anything.

Do i need to connect the dash to car and then do Digiprog?
Do i need to program the digiprog unit by PC or so before using it?

I have also tried HC12 and HCS12 both give same "INIT ERROR"