Digiprog 3 clone questions and answers

[letalcrudo]

Hallo my digi no Read 95160. Any Solutions?

Wysłane z mojego SM-G390F przy użyciu Tapatalka

do you read on circuit or desolder the eeprom and put in adapter?

[Nicolas9]

Desolder and clean chip.

[hoangtu]

hi! Anyone have a repair solution to be able to read Motorola 05H12? thankyou very murch!

[rtbdiagnostic]

I've tried on Amarok from 2011-2015... I had success on 8/10 ... V4.88

Attachment 562461

I eventually used x300m to fix the 2015 vw amarok dash quick job

[letalcrudo]

I eventually used x300m to fix the 2015 vw amarok dash quick job

I'm making up my mind about buying that tool or smok...

[Cyber Hunter]

Hello everyone,

I need help for toyota prius mk2, i've just open a new thread for that here: http://www.digital-kaos.co.uk/forums...ection-(93CS66)

So if somebody know how to do that it would be wonderful !

thanks in advance

[nagy592]

Citroen C5 2003 Sagem BSI- changing mileage, ok. I tried the dashboard (HC08) with plug 42, no luck. I checked the pinout first and that seems correct. I had four connection attempt and failed all the time. I'm going to get Carprog to do the dashboard. Anyone has success with CP (clone obviously) on this? Thanks

[hipolitogt]

Hi, somebody successfully did a 2015 fiat scudo (same as Peugeot expert/ Citroen jumpy dispatch/ Toyota proace)? Customer installed and used JC bsi and now car has more mileage and need to downgrade it. Never used this tool, and a friend let me his tool to make the job.

Enviado desde mi SM-G960F mediante Tapatalk

[Music73]

Hi, somebody successfully did a 2015 fiat scudo (same as Peugeot expert/ Citroen jumpy dispatch/ Toyota proace)? Customer installed and used JC bsi and now car has more mileage and need to downgrade it. Never used this tool, and a friend let me his tool to make the job.

Enviado desde mi SM-G960F mediante Tapatalk

Hi

These are ok with digi..

95128 in the bsi.. it is covered in lacquer.. so need to remove that first.. can be done on the board but safer to remove.. you need to do dashboard also which is a 25020 I think... but again digi can do no problem..

Sent from my SM-G935F using Tapatalk

[hipolitogt]

Hi

These are ok with digi..

95128 in the bsi.. it is covered in lacquer.. so need to remove that first.. can be done on the board but safer to remove.. you need to do dashboard also which is a 25020 I think... but again digi can do no problem..

Sent from my SM-G935F using Tapatalk

Thank you!!!

Enviado desde mi SM-G960F mediante Tapatalk

[wbart]

do you read on circuit or desolder the eeprom and put in adapter?

Eeprom desolder and read only ff

Wysłane z mojego SM-G390F przy użyciu Tapatalka

[honingkoning]

Jeep grand Cherokee 96 with digi (4.85) ok.

[wbart]

Hallo mates
My digi work kline and can ok but eeprom Read bad. What with it ? Any Solutions?

Wysłane z mojego SM-G390F przy użyciu Tapatalka

[wbart]

I have 2 digiprogs. Both work ok for OBD but one of them will not read all eeproms. One of them is fine but the other will only read 95xxx eeproms and not 93cxx or 24cxxx. I suspect there is something wrong with the buffer chips (hc125's etc). The problem is that all of the chips have had the tops ground off so I don't know which chips to change. Can someone help me with this please.

Hallo .
Ihave the same problem. Resolve you problem? Mayby anyone have solutions?

Thanks

[davecooper47]

Yes. I just bought a new one. They’re so cheap now.


Sent from my iPhone using Tapatalk