The remote part of the key should be seperate from the transponder. It's a manual process to program the remote in and second hand remotes can be used.
Hi
Anybody knows something about remote control locking in this model ?
How it works ? I know that it is separate box one for immo and one one for remote locking but it is possible to write used fob to get it work? PCB is very similar to other peugeot like 206 ...
I didn't find any connection of remote box to diag socket or immo box just stand alone ?
Even if trnsponder is match with FOB how info to remote lockng box is transfered when program new key....
The remote part of the key should be seperate from the transponder. It's a manual process to program the remote in and second hand remotes can be used.
i did a remote for a aygo the other day the process is a little different than the normal toyota remote procedure
Could You describe how to program used remote ?
Time bump this old thread.
Bought myself a Peugeot 107 1.0i, but it only has one key and I would like to make an other one. I want to use a USED remote. (Buy a used 107 key fob with PCB and buy a new housing with uncut blade from Ebay. Have it cut, than install the used PCB in the housing)
How can I program the immobilizer and remote to
1. start
2. open & close
the car?
programme the chip by obd id70 if you have a working key and programme the remote seperately
Procedure to rpegram remote:
-put ignition on then off
-open and close driver doors 2x (leave open)
-put ignition on then off
-open and close driver doors 2x (leave open)
-close driver door
-lock doors
-put ignition on and off 2x
-open driver door
Now you are in programing "mode" press lock door on remote 2x remote shuold be added.
dexter321 (19th November, 2017)
Would the aforementioned procedure work with used remotes? (so adding a remote which was previously used by an other car)
Additionally, is the 107 remote the same as the usual Peugeot 206 / 307 / etc. remotes?
Or should I buy a 107 specific used remote - being Toyota related, so maybe a bit different!?
Second hand remotes can be used, just replace the transponder chip to start the car.
Second hande remote fob will work but must be from 107 aygo etc. 206 will not work i tried program without success
Hi mate
if you just want a second key for 107,C1 or Aygo you can use any second hand key, as long as it's from a 107 or C1 or Aygo, and you don't have to replace the chip.
They use toyota type 4D chip and all you have to do is add a key using Peugeot Planet or Lexia I believe you can use AD100 too but I haven't tried it.
If all keys are lost you have to virginise the immo box but if you have a working key all you have to do is add the second key.
It will ask the question 'do you have a key' you press yes then continue on.
Done hundreds of them!!
Happy New Year !!!
Hi. Thank for istruction
Last edited by dexter321; 19th November, 2017 at 01:32 PM.
NOTE : Ensure Ignition switch in OFF position and driver?s door open.
NOTE : This procedure must be completed within two minutes.
1. Switch the ignition ON and OFF.
2. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.
3. Switch the ignition ON and OFF.
4. CLOSE and OPEN the driver?s door TWICE – so door ends up in the OPEN position.
5. CLOSE the driver?s door.
6. LOCK the door using the door lock button on the door.
7. Switch the ignition ON and then OFF.
8. UNLOCK using the door lock button on the door - the locks will cycle to indicate programming mode.
9. Remove key from ignition.
NOTE : Some models require you to leave it in the ignition.
10. PRESS and release both LOCK and UNLOCK buttons on the remote transmitter.
11. PRESS and release LOCK button on the remote.
lion0304 (19th November, 2017), marcin7091 (15th May, 2018), rob h (26th December, 2017)
Bookmarks