Can Anyone Help me Please???
Can anyone confirm if this LPT parallel port jtag Programmer For ARM H-JTAG is valid to reprogram Carprog Mcu AT91SAM7s256. I guess if possible because is ARM7... but need you confirm this.
$(KGrHqJ,!lIFD)kbnB99BQ-2vDUCTg~~60_12.JPG
http://www.ebay.com/itm/251216595416?ssPageName=STRK:MEWAX:IT&_trksid=p398 4.m1423.l2649
And further question is if i can connect this programmer to LPT port to Usb Cable Adapter and this not create conflicts to do reprogramming.
Advanced Very Thanks for your help.
Can Anyone Help me Please???
hi can u help me when i click on program 2-3 sec and a error: time out massage pop up
thanx
benzerrouki (16th November, 2014), ferchichi (11th March, 2018), Oto kilitsan (16th January, 2021), ruffles1986 (1st April, 2013)
're-flash possible without removing AT88SC eeprom'
How many people have done this with full success? Any failures of the eeprom data yet?
Could upa or xprog be used to read/write & backup this as a failsafe?
Thanks guys for your help!
Can someone please clarify a newbies confusion :-)
#1 picture 4 shows the pin 55 link wire going to JP1 solder point nearest the USB end of the CP
to enable flash erase. The next picture in #2 shows a link wire the other end of the JP1 to erase.
Which is correct please?
Credit to audiotek on making the programming software steps with pictures nice and clear!
I understand that i can use the Ltp wiggler with the H-Jtag software to reflash the AT91SAM.
If i want to use the usb J-link V8 does it still use the same software and settings?
(sorry if this is a dim question...just trying to be foolproof - i should have asked on 1st April :-)
Are the connections correct in #149 for the J-Link?
Thanks to all
Hello my Friend
Can you help me please with this error from JTAG
Can you tell me what I'm doing wrong
Look the photo pleasefault from jtag.rar
Regards
You'll need to erase the Atmel correctly, if you don't erase the Atmel content the Jtag port remains closed, pleaase look at post #1 : "Wait from 5 to 10 seconds after connect the 12v supply, the flash content will be erased and the Jtag option of the Mcu will be enabled now. If not work leave connected for about 3 to 5 minutes. Disconnect the 12v supply from carprog and remove the pin 55 wire from vcc. The pin 55 must remain disconnected until the programming process is done." For Jtag pinout check the post #2.
Xprog Box Original, UPA Original, GromCalcTool,TL866A, Willem PCB50, Masterprog, NecProg, Orion, Ponyprog, Carprog, Renesas H8SX, MT60/80, SPC560 programmers,Obdstar X300DP, EZ500, CHIPSOFT MID,SKP1000,Cantool, SuperVag 3.0, Vag Commander, Vagcom Original, Launch x431 Pad, Witech OEM, Ford VCM II OEM, Mazda VCM II, Volvo Vida-Dice, Hyundai & Kia GDS, MUT III, Mastertech VCI, EASE j2534, Ford & Mazda VCX, TS401, Cardaq-m, DIS 5.7, VAS5054 Plus, Tachopro 2.0 & 2008.01, Vag K+Can, JLR v141.....
I have erased the atmel 5-6 minutes to the ground because for 10 second does not erase
May have burn the atmel? because I left it on the ground a little more than 5 minutes
VDD of the photo is VCC from the jtag??
TCK is TCLK from JTAG???
NRST is TRST from JTAG ???
The reset of the JTAG who to connect ???
Thanks!!!
Look this video please MOV02266.rar
Erased the Atmel to ground? you'll never erase the atmel connecting the pin 55 to ground, as you can see in the post #1 the connection is to vdd test point of carprog, you need to make the erase procedure before to connect the carprog to the programmer. And yes, TCK is TCLK, NRST is TRST or RESET (doesn't matter, if you test continuity in programmer you can see that TRST and RESET are the same pin).
Xprog Box Original, UPA Original, GromCalcTool,TL866A, Willem PCB50, Masterprog, NecProg, Orion, Ponyprog, Carprog, Renesas H8SX, MT60/80, SPC560 programmers,Obdstar X300DP, EZ500, CHIPSOFT MID,SKP1000,Cantool, SuperVag 3.0, Vag Commander, Vagcom Original, Launch x431 Pad, Witech OEM, Ford VCM II OEM, Mazda VCM II, Volvo Vida-Dice, Hyundai & Kia GDS, MUT III, Mastertech VCI, EASE j2534, Ford & Mazda VCX, TS401, Cardaq-m, DIS 5.7, VAS5054 Plus, Tachopro 2.0 & 2008.01, Vag K+Can, JLR v141.....
shadab (14th November, 2016)
Can someone please answer the connection questions here please?
To erase AT91SAM pin 55 linked to where? picture in post #1 or post #2 correct?
#1 link.jpg#2 link.jpg
Are the jlink connections in the picture post #149 correct please.
J-LINK TO CARPROG.JPG
Thanks
I still was not clear whether the use 74HC125 (CMOS level) or 74HCT125 (TTL levels)? I think that's the main problem with the clones....
Is somebody has pinout for RNS510 adapter..china clone has DB25 from one side and wires to second side...but, question is, where to solder wires on RNS510??
The origin has conectors from both side.
cuby
Bookmarks