Pin 2323 IS CORRECT
Hello friends!
Need your help. Car Opel Zafira 2003 Y20DTH PSG16 swap Pump. I read the dump from the pump through Carprog clone and now I need the correct pin to make reset.
Pin 2323 - wrong!
The data from the diagnostics:
VIN: W0L0ZCF6838056005
vehicleManufacturerECUHardwareNumber 24451346 KD
systemSupplierECUHardwareNumber: BOSCH010000001401
systemSupplierECUHardwareVersionNumber: 0000
systemSupplierECUSoftwareNumber: DJAMS120_S
systemSupplierECUSoftwareVersionNumber: 0774
exhaustRegulationOrTypeApprovalNumber: B02008
systemNameOrEngineType: Y20DTH
Thanks in advance for any help.
Last edited by Dynamitik; 30th September, 2012 at 07:14 AM.
Pin 2323 IS CORRECT
you have two choices in the morning: go back to bed and continue dreaming, or you get up to make your dreams come true
OP-Com: Engine->Programming->Reset ECU Login: 2323->Login incorrect->Op-Com Diag Engine-> P1611 - Login wrong + activated wait time
OP-Com: Immo(Immo alredy Reset)->Special Functions->Login: 2323->Reset ECU->Login incorrect->Op-Com Diag Engine-> P1611 - Login wrong + activated wait time
Car-Prog: Login: 2323->Reset Pump->Op-Com Diag Engine-> P1611 - Login wrong + activated wait time
What are some other ideas?
Who can to VIN-number to find out information about the car. Maybe this pump Opel Vectra-C.
VIN: W0L0ZCF6838056005
Thanks in advance for any help.
If you want to install Zafira pump to Vectra, then the pump must be reseted on Zafira. You can not reset Zafiras pump on Vectra-C!
W0L0ZCF6838056005 = Y20DTH engine. Its a Vauxhall.
Last edited by gaz51; 2nd October, 2012 at 03:53 PM.
I dont think that is posible to get work vectra C pump on zafira.
i read somewhere , you can reset it on bench , and it will work...search the forum m8
Dosen't matter how hard is to repair something as long is made by humans and thinked by humans !
Hi, Clone carprog "opel / ECU / can bus" not working!! This will surely say, because I tried several models. The download mark in just bounce on and not connected to the ECU.
I have put Vectra C psg16 pump into Zafira A. The Bosch number was the same, but it had to be replaced and the software reprogrammed.
With original carprog the reset not problem, but maybe After mounting, the Zafira A, it will seek companions CANbus, such as UEC, REC, CIM ...... , try to find someone near you who is original and carprog and you doing reset on table, after put into the Zafira A, then update the software that the car should be.
Otherwise the pin 2323 may not be bad, but does not allow to recover the OPCOM as the Vectra C CANbus system and the Zafira A K-line.
If deprogrammer and Zafira models you will not find a CANbus companions.
Last edited by kardi78; 4th October, 2012 at 09:02 PM.
hi i need please you help dr menbers for conect the ecu m.1.5.5 of corsa city with the carprog
i need the pin to read the ecu please
thanks
connecting it to the OBD carprog for, selecting the k-line folder m1.5.5 bosch software, and then "read all" principle reads the content and get the correct PIN
if not, the Chinese can not clone it!
Hii, necesita código PIN psg16..thanks
Bookmarks