XPROG Clone Repair

**Zmann** · 15th April, 2013, 09:41 AM

Thanks stef, really? you knew i didn't lock it

have you tested that way?

Ok I will try again sometime later.

**gabardo** · 2nd May, 2013, 10:27 AM

Good morning to all the forum, anyone can tell me where to buy .... XPROG-M V5.3 clone but works perfect.
I've comprodos two and I had to return, not working
Greetings ...... Gabardo

**djdanny** · 4th May, 2013, 06:11 PM

hi i have x-prog, i try read "0h57a"
xprog say: xprog "vcc" pin overloaded. check "vcc" pin connection
please help, how to repair?
What am I doing wrong?xprog.JPG fotó 2 (1).JPG fotó 1 (2).JPG

**Zmann** · 5th May, 2013, 12:47 AM

We cannot use HC05Bxx adapter for HC05H12 chip

**zoro1** · 5th May, 2013, 05:42 AM

Originally Posted by stefaudio

Hi Zmann may be if you lock Atmega procesor, counter will go off.

No.Comunication eeprom-flash in RISK MCU like Atmel is not depend form fusebits or lockbits.
I think counter is conected with soft too...
If some one that has debugger AVRDRAGON to seewhat is going inside when is working.

**Zmann** · 5th May, 2013, 07:00 AM

you found the same, counter is still?

**djdanny** · 5th May, 2013, 08:20 AM

Originally Posted by Zmann

We cannot use HC05Bxx adapter for HC05H12 chip

how to read?

**Zmann** · 5th May, 2013, 09:44 AM

As the chip has been removed, follow the manual diagram 2.1.7. MC68HC(7)05H12. Try to conect all wires manually. AND a xtal of about 4MHz to pin 1 and 52 together with a resistor of about 5-10 Mohm to the same pins. Notice that Xprog is presetting the clock as 4.19 Mhz for this chip if you use 4Mhz reset it to 4MHz too.

**djdanny** · 5th May, 2013, 10:25 AM

Originally Posted by Zmann

As the chip has been removed, follow the manual diagram 2.1.7. MC68HC(7)05H12. Try to conect all wires manually. AND a xtal of about 4MHz to pin 1 and 52 together with a resistor of about 5-10 Mohm to the same pins. Notice that Xprog is presetting the clock as 4.19 Mhz for this chip if you use 4Mhz reset it to 4MHz too.

bypass security stopped. red lamp iluminated...iwait...nothing happens.

**Zmann** · 5th May, 2013, 10:55 AM

No. remove the adapter off Xprog and connect all wires directly and only to Xprog 16-pin terminal.

**Dunker** · 5th May, 2013, 11:24 AM

I wonder why the counters initial value is D0h? Did that just happen to be the value when the chip was originally cracked/read? I wonder what will happen if the counter is set to FFh before programming the MCU. Using the tut from this thread has made my clone a lot better. To be fair the only trouble I have had since updating is a verify error on the flash in a 908AZ60 from a Renault parking brake module. Its no real hassle to reprogram the MCU from time to time anyway if the counter situation does cause verify errors.

**user2468** · 10th May, 2013, 07:18 PM

If counter is active then xprog do verify error.

**didi_du_93000** · 11th May, 2013, 02:50 AM

Hello All,

When i read securised 9S12XDP512 from CAS3 i have verify error.
but with eeprom, TMS... haven't verify error.
It's XProg M V4.5 (first version from china with metal box).

When i read a 908 with xprog m and compare with dump from ETL i have not the same dump.
I have many error in xprog M dump.

Maybe it's hardware problem?

**zoro1** · 23rd May, 2013, 02:46 PM

On what MCU is veryfy error?I will try to connect atmega with JTAG debugger to see where is conection flash -eeprom and what is change inside .Counter is activatin with reading eeproms too?

**maaxxyy** · 25th June, 2013, 02:59 AM

Hi guys i think i bricked my xprog 4.5 as i plugged it in by mistake whilst the 5.3 software and dongle was loaded. Now i get error when choosing the usb port 'incorrect device range'. Anyone had this issue? Is it recoverable? Thanks

Managed to sort it out, just run the software set up again, clicked on repair software and all working well again.