XPROG Clone Repair

**Master01** · 3rd October, 2013, 08:11 AM

New software version is available for original X-ProgBOX users.

V5.0.0

Added new devices...

**serg2000** · 9th October, 2013, 06:11 AM

Please upload version 5.4.9

**user2468** · 12th November, 2013, 01:34 PM

eldb XPROG

**Norman Semos** · 27th November, 2013, 08:20 AM

I can say nothing but thanks

**carmelasse** · 18th December, 2013, 01:43 AM

I haved working v5.0 (metal case) xprogm but when I programming some HC9S12 processors I have verify error.

Well, yesterday I update ATmega64 with flash and eeprom from this post.
And when switch fuses and LockBits like on this pictures i have "Device is silent" and XprogM is dead

(RS232 and USB)
qnze.jpg<=>u2j0.jpg

But, when I enable Fuse "Watchdog" and program to Atmega64, my xprog is detected in program, but no any information and authorisations.
Now i have no any authorisations and no any data in info (see pic).
97an.jpg 3kmw.jpg

Please any help or ideas?
Needs to program 93c46 ? 93c46 its only for USB connection?

Regards

************************************************** ************************************************** ******
SOLVED!!!
My shitty ISP programmer (Propox ISPcable II) always program fuse "Boot reset vector enabled (default adress=$0000);[BOOTRST=0)", even if I unmark this fuse.
I use other XprogM and all programmed ok.
I need to buy a better ISP Programmer

Regards

**mahmod_q** · 25th December, 2013, 05:41 PM

hi
any one have dump for x-prog 5.3 or 5.4

**spiridonas** · 3rd January, 2014, 03:12 AM

Hi guys I try to update the firmware in the my clone xpog with edbl software 5.50 and after success update when run xprog 5.0 software says message device silent
Please how I can to back again to previews state.
I have and other original xprog but I can to reflash with this tool the atmega 64 from updated (damaged) clone xprog
Thanks

**PartyTwist** · 17th January, 2014, 02:49 PM

Thank you for all the info!
So there're still no 5.4.5 or 5.4.8 dumps?

heteromies · 21st January, 2014, 09:01 AM

Please tell how to take dump, i can try?

**maax990** · 6th March, 2014, 08:54 AM

Hello,image rescued Xprog programmer tl866a

Stawianie xproga fusy dobre.JPG

the best thing is to set Fuse

Fuse low byte:0x2F
Fuse high byte:0xCA
Extended fuse byte:0xFF
Lock bit byte:0xEB

To load both files together with the set Fuse byte

sorry my english

**serg2000** · 7th March, 2014, 04:45 PM

lock bits not correct

**maax990** · 7th March, 2014, 07:34 PM

2 xprog program this lock bits,all work perfect

**looly** · 13th March, 2014, 01:09 PM

My xprog-m clone which I had with dongle v5.3 had problem reading MPC processors, always got stuck on "initialising device". I downgraded to v5.0 without dongle and then it was working fine. Suddenly i started to get the "verify error" problem so i thought solution was to use dumps from 1st post in this thread. Since changing firmware to the one in the 1st post of this thread I can no longer read MPC561 as I always get "initialising device". I can read eeproms fine. I saved original eeprom data but (stupidly) forgot to save original flash data. Anyone able to shed some light pls?

Thanks

All options are authorized

**PartyTwist** · 13th March, 2014, 02:15 PM

Just a note, you probably didn't get the correct data when you read the "original" eeprom/flash as it's protected (and the software checks that it's protected before continuing work).

**looly** · 13th March, 2014, 02:35 PM

Originally Posted by oxygenium

Just a note, you probably didn't get the correct data when you read the "original" eeprom/flash as it's protected (and the software checks that it's protected before continuing work).

Thanks, I dont feel so much of a fool now

.

Any solutions pls?