Jlr Evoque key not found

[rob h]

A 2014 Land Rover Evoque.


Car had trouble switching ignition on for some time. Up to the point, that it does not comes on anymore.
Both oem keys, remotes when pressed do open close the doors.
When i push start button, key is not found.
So when i hold the key to the steering colum coil. The message wrong key appears.


I have added a key, by obd, Direct in to the Kvm. This key, does exact the same as the 2 oem keys.
Only remote work. (ignition does comes on, during obd key programming procedure, and unlocks elv during this)


When i read the bcm, using vvdi prog, it tells me, partition information error.
It does allow me to read a 32K D-flash.


Is the bcm data corrupted? Could this explain, why the file is not recognised?
When i load it in Tango.

D-flash.rar

[fred77]

Hi rob, 1st try disconnecting battery for few seconds if havent done.

Have you SDD?
-might be worth looking at fault codes and running thro 'security' on menu to resync.

if still no joy reset KVM to default and code in as new module

[rob h]

Battery, they replaced, so that covers the disconnect.
I will try the synch

[darek748]

Is there anything displayed on the speedometer screen?

[darek748]

I recently had a case in RR sport only the hand brake was on
in speedometer screen

[rob h]

It does turn on, and display full, when my key programmer tool, forces ign on.

When the ignition is no longer forced on,
The display works, but i did not pay attention to the handbrake led .

[Manta1600]

Looks like faulty keyless antenna

[darek748]

in my case there was a corrupted dump in bcm cleaned up
I just uploaded I don't remember now but I think dflash on one of the processors (there were 2)
and the ignition got up
it was RR SPORT 2018

[fuzz1]

in my case there was a corrupted dump in bcm cleaned up
I just uploaded I don't remember now but I think dflash on one of the processors (there were 2)
and the ignition got up
it was RR SPORT 2018

Hi
Where did you get the dump you uploaded? Did you fix it or got a working one?

[darek748]

I bought a used bcm and copied only one dflash which was broken

[darknezz19]

Post kvm number and we'll try to find virgin file. Maybe it could work.

[rob h]

IMG_20230104_175845288.jpg Avdi kvm info.jpgThis is a picture of the kvm.

And here is a immo function, avdi provides. When i press read, i gett succesfull after about 1 minute, and it shows only zeros.
Does here, suppose to stand a sync code?
Avdi SK.jpg

And the pats info
------ (PATS) information ------
BCM: Ignition ON Success
BCM: C124 04040404
BCM: C190 00000400
BCM: KeyNo 0 6CEFCD 33
BCM: KeyNo 1 C608CE 33
BCM: KeyNo 2 FFFFFF FF
BCM: KeyNo 3 FFFFFF FF
BCM: KeyNo 4 FFFFFF FF
BCM: KeyNo 5 FFFFFF FF
BCM: KeyNo 6 FFFFFF FF
BCM: KeyNo 7 FFFFFF FF
BCM: Variant 11 "EJ32-14C256-AC"
PCM: Variant 10 "BJ32-12B684-VB"
IPC: Variant 2 "DPLA-14C449-AB"
AKE: Variant 7 "DPLA-14C104-AC"
AKE: 8004 Check all Learned Keys Success
AKE: Number of keys programmed: 3
AKE: KeyNo 0 6CEFCD 33
AKE: KeyNo 1 D61A71 33
AKE: KeyNo 2 518DEF 3B
AKE: 8005 Check Transceiver Communication Success
AKE: 8006 Check all antennas Success


So i have 2 oem keys, in the bcm
And 2 oem, plus 1 i added in the kvm.

B1B01:55-2E
This dtc, in the kvm accurd 127times.

[fred77]

Before taking anything off car I'd get SDD it'll check everything - it'll do a software update on that KVM from JLR server.
Did a XF today that year same module. SDD was a pain the the bum took over hour (kept requesting update) but added key.

Be carefull of AVDI as it can modify p-Flash on key programming. Autel seems ok thus far but security too much bless it for XF today

[issam216]

Tomorrow i will send virgin dump write it to the kvm and program your keys .. easy to fix any fk72 virgin dump or dpla virgin dump just be careful when soledering pinout evoque 2014 always fail in obd programming there nothing to worry ..

[issam216]

write those virigin file to kvm and adapt keys with obd.