AUTOCOM 2013.3 DOWNLOAD AND INSTALL INFO

**benzerrouki** · 1st February, 2013, 10:21 PM

Hi mates i need the patch for autocom 2012 release3 thanks

**1704E3** · 1st February, 2013, 11:20 PM

version 2012.2

cdp+ cars
id ; a-710-142
HARDWAREKEY ; EYGRNVNMRBAO
serial ;100251
this is the fileactivation.xml
FileActivation.rar
thanks

**mitko_2** · 2nd February, 2013, 07:19 AM

Originally Posted by benzerrouki

Hi mates i need the patch for autocom 2012 release3 thanks

Here patch for autocom 2012

**toalecs** · 2nd February, 2013, 09:45 AM

Originally Posted by 1704E3

version 2012.2

cdp+ cars
id ; a-710-142
HARDWAREKEY ; EYGRNVNMRBAO
serial ;100251
this is the fileactivation.xml
FileActivation.rar
thanks

Read the title again, this thread is about 2012 R3...

**ex250** · 2nd February, 2013, 10:13 PM

Hello, please me too!
Autocom 2012.3

a-710-142
100251
OPCSPRBDMRMQ

**micron6** · 3rd February, 2013, 01:15 AM

Originally Posted by kostas

sonho1999...........

hello
actived
2012.3

**micron6** · 3rd February, 2013, 01:18 AM

Originally Posted by ex250

Hello, please me too!
Autocom 2012.3

a-710-142
100251
OPCSPRBDMRMQ

Post #33
Here patch for autocom 2012 Attached Files

patch installation 2012.3.rar (12.07 MB, 14 views)

**DiagService** · 3rd February, 2013, 10:38 AM

HI guys I need patch instalation for Delphi 2012.3 DS-150
thanks

**autocargo** · 3rd February, 2013, 11:21 AM

Originally Posted by DiagService

HI guys I need patch instalation for Delphi 2012.3 DS-150
thanks

It's the same patch as for Autocom 2012.3

**AKAINTERN** · 3rd February, 2013, 02:06 PM

Originally Posted by ex250

Hello, please me too!
Autocom 2012.3

a-710-142
100251
OPCSPRBDMRMQ

You first install the patch, then save the file FileActivation !

**DiagService** · 3rd February, 2013, 06:39 PM

Originally Posted by autocargo

It's the same patch as for Autocom 2012.3

I have install Delphi DS 150 I have copy patch file from Autocom 2012.3 in folder wit DS 150 when I write S/N and H/D numbers and try my USB Stick Than I have in new window (failed to prepare usb stick. you have to use manual mode or try again)
Have you any Ideea ???

**ex250** · 3rd February, 2013, 08:56 PM

Originally Posted by AKAINTERN

You first install the patch, then save the file FileActivation !

Thanks! installed the patch and found a working "kg", program now starts, gone to the hardware config, but not can do the test to the vci (is recognized as cdp+), firmware update fails too... after that program feels "hanged" and difficult to close it.

Will try to install older 2012.2 to see if there is any change.

**smirnoff_rules** · 3rd February, 2013, 08:57 PM

Originally Posted by ex250

Thanks! installed the patch and found a working "kg", program now starts, gone to the hardware config, but not can do the test to the vci (is recognized as cdp+), firmware update fails too... after that program feels "hanged" and difficult to close it.

Will try to install older 2012.2 to see if there is any change.

u are trying to update connected to a car or 12volts ?

**smirnoff_rules** · 3rd February, 2013, 10:10 PM

is no one reading the forum rules anymore

**Dunker** · 3rd February, 2013, 11:10 PM

My interface is the single PCB type. All updating done on workbench not connected to a vehicle. I installed 2012r3 (firmware updated to 1230), everything ok. Installed on second laptop (1st laptop was for testing) and all still ok. Updated 2nd laptop online to 2012r3.2 and firmware updated to 1231. Hardware test failed. Went back to first laptop (first install 2012r3) and clicked update firmware - this took firmware back to 1230. Tried again on 2nd laptop and it worked this time. Software at 2012r3.2 and firmware 1231. What I will say is that maybe its because the second laptop is USB3. I will connect to a few cars at work tomorrow and post if there are any issues. But at least for now it looks like the online update works and any connection problems (hardware test) is a hardware issue and not a serial number issue.