Xprog 5.5.1 Atmega and eep free for all - Page 14
Register
Page 14 of 15 FirstFirst ... 49101112131415 LastLast
Results 196 to 210 of 218
  1. #196
    DK Veteran

    Join Date
    Oct 2016
    Posts
    349
    Thanks Thanks Given 
    78
    Thanks Thanks Received 
    125
    Thanked in
    70 Posts

    Default after i programmed my atmega by AVR

    what should I check or uncheck in avr fuse & lock bits
    Attached Images Attached Images

  2. #197
    DK Veteran

    Join Date
    Aug 2009
    Posts
    314
    Thanks Thanks Given 
    2
    Thanks Thanks Received 
    9
    Thanked in
    8 Posts

    Default

    Hello
    Help me Please
    I do atmega 64 with upa USB erase error
    Flash error
    What is it problems?

    Regards
    Attached Images Attached Images

  3. #198
    Newbie
    Join Date
    Jun 2014
    Posts
    7
    Thanks Thanks Given 
    9
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    xprog avr.jpgI found this.

  4. #199
    DK Veteran zoro1's Avatar
    Join Date
    May 2010
    Location
    Bulgaria,Sofia,Vidin
    Posts
    530
    Thanks Thanks Given 
    93
    Thanks Thanks Received 
    417
    Thanked in
    50 Posts

    Default

    I updatre my years ago ,working good on XP ,and 7 64 bit.I try some 555 soft from net ,but no working good.I use this with internet ON with no problems.I manage to add atmega 10 ISP port on one side for reprograming atmega inside xprog and no open it.Inside there is two ping mark GND ,on my AVR 910 programmer is conection to be able to program atmega.For special case/fuse bit wrong!/ i add Xtal1 to ISP too,if i lock my atmega !Thanks LAndre and Adam 28 for good JOB!!!But i was try to read MPC 551 ,read all ok /edc16c34 KIA/ then erase flash ,erase eeprom ,then try to write flash and there is error on 80,68,98 % -writing failed!Conection is standart BDM Bosch with ext 12 volt.
    Last edited by zoro1; 7th August, 2018 at 11:20 AM.
    Large nations behave like gangsters ,and young as prostitutes !

  5. #200
    Newbie
    Join Date
    Mar 2017
    Location
    Poland
    Posts
    6
    Thanks Thanks Given 
    2
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    I have updated and now I have the error unknown command software error

  6. #201
    DK Veteran
    xoom's Avatar
    Join Date
    Dec 2009
    Location
    Ylakiai
    Posts
    385
    Thanks Thanks Given 
    30
    Thanks Thanks Received 
    336
    Thanked in
    70 Posts

    Default

    Quote Originally Posted by memore34 View Post
    I have updated and now I have the error unknown command software error
    did you set lock bits?

  7. #202
    DK Veteran
    Tecdiag's Avatar
    Join Date
    Oct 2012
    Location
    Algeria
    Posts
    444
    Thanks Thanks Given 
    218
    Thanks Thanks Received 
    114
    Thanked in
    62 Posts

    Default

    hello all, please does someone know the pinout connection and lockbits, fusebits configuration to read atmega64 and update my XprogM with upaUsb .
    If you can not fix it, please leave it as it cameIF I HELPED YOU PUSH THANKS AND REP BUTTONS

  8. #203
    DK Veteran
    alfons37's Avatar
    Join Date
    Sep 2009
    Posts
    1,106
    Thanks Thanks Given 
    260
    Thanks Thanks Received 
    95
    Thanked in
    48 Posts

    Default

    I have update to 5.51 and all work, but i must restart software every time if i read one time. If i no do it hangs on reading. What is wrong?

  9. #204
    Newbie
    Join Date
    Dec 2018
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    function?or not?

  10. #205
    Top Poster

    Join Date
    Oct 2015
    Location
    Poland
    Posts
    124
    Thanks Thanks Given 
    161
    Thanks Thanks Received 
    8
    Thanked in
    8 Posts

    Default 5.5.1.txt

    Hi, I am asking for 5.5.1.txt I can not download it. Thank you in advance

  11. #206
    Senior Member
    Becoacamba's Avatar
    Join Date
    Sep 2009
    Location
    AnyWhere
    Posts
    276
    Thanks Thanks Given 
    39
    Thanks Thanks Received 
    50
    Thanked in
    25 Posts

    Default

    Quote Originally Posted by tom222 View Post
    Hi, I am asking for 5.5.1.txt I can not download it. Thank you in advance
    IT'S WORKING RIGHT

  12. #207
    Member
    Join Date
    Jan 2016
    Posts
    60
    Thanks Thanks Given 
    18
    Thanks Thanks Received 
    2
    Thanked in
    2 Posts

    Default

    thanks, hope will be helpful

  13. #208
    Newbie
    Join Date
    Oct 2015
    Posts
    13
    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Hello Adam, I was able to update but when I read any memory it gives me a message from unknown command, software error, do you know how I can solve ?? my xprog-m was version 5.84 clone but I couldn't find the certificate anymore ...

  14. #209
    Newbie
    Join Date
    Aug 2019
    Posts
    5
    Thanks Thanks Given 
    2
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Thanks!!!!

  15. #210
    Top Poster
    Join Date
    Mar 2017
    Location
    TÜRKİYE
    Posts
    138
    Thanks Thanks Given 
    32
    Thanks Thanks Received 
    14
    Thanked in
    12 Posts

    Default

    I'M GETING A PROBLEM WITH ME I NEED TO DO WHAT HELP

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.