Hi
Citro?n Picasso 2009 with BSI and 95128 eeprom / Johnson Controls.
DP3 has done writing the new km value by "flashing" by OBDII "reading, verifying, writing" but only until 99 %.
Now car is "dead" , no functions anymore.
Need to tell also that i forgot to put extra battery charger, so this was happen when voltage dropped and now car is "dead"
Re-write with DP3 is possible apparently, recognise BSI number (but NOT the VIN) and does automatically pick-up the saved
"flash-file" and will try to recover, BUT DP3 dont flash anymore when arrived @ 99%....
EEprom data looks oke, but i have no idea how to solve this problem !
Put all FF in eeprom also dont wake up the car
Any clues or suggestions ?
Thanks in advance
Results 1 to 15 of 310
-
4th January, 2015, 03:46 PM #1DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
CITRO?NN PICASSO 2009 / BSI FLASH PROBLEM
-
4th January, 2015, 04:06 PM #2DK Veteran
- Join Date
- Jan 2010
- Posts
- 449
- Thanks
- 65
- Thanks
- 103
- Thanked in
- 44 Posts
flash BSI with FVDI or SMOK PSA tool, give reference number on label
96xxxxxxxx
BSI 20xx xxx- xxxxxxxx
BOOT xxxxxxxx
HARD xxxxxxxx
xxxxxxxxxxKTAG, PCMFlash, Galetto FGTech V54, Smok Multitiool UHDS, I/O Terminal, Fiat/Alfa IAW Bosch Decoder, UPA-USB, XPROG, FVDI, Orange5, Renolink, DiagBox, Can Clip, Xentry
-
The Following 2 Users Say Thank You to sl4ck For This Useful Post:
boris93600 (2nd May, 2018), pouettedu76 (22nd January, 2017)
-
4th January, 2015, 04:23 PM #3DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
i do not have SMOK or FVDI
PSA = 96 640 590 8002
V 05.01
281201930C
N805243015
boot 28120836-4
hard 28119248-3 C
BSI 04 EV K04 - 00 020309
-
The Following User Says Thank You to CARPARTS For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 04:34 PM #4Member
- Join Date
- May 2012
- Posts
- 70
- Thanks
- 25
- Thanks
- 23
- Thanked in
- 10 Posts
Here is your eep file. If from a C5 2.0 hdi 2009.
966405908002
bsi04ev k04-00 -81209
b28120836-4
hw 281192483c
v05.01
281201930c
read1 bsi m95128.rar
-
The Following 3 Users Say Thank You to tziku For This Useful Post:
A630V (19th August, 2018), boris93600 (2nd May, 2018), willyboy28 (15th February, 2021)
-
4th January, 2015, 05:24 PM #5DK Veteran
- Join Date
- Jan 2010
- Posts
- 449
- Thanks
- 65
- Thanks
- 103
- Thanked in
- 44 Posts
He needs flash i think, if eeprom data is ok, flash is messed up.
Don?t know if you can do anything with easyCAN4, it has jtag interface, but don?t really know if it is solution to flash over jtag.
http://www.scaleochip.com/images/Pdf...32-BRF-200.pdfKTAG, PCMFlash, Galetto FGTech V54, Smok Multitiool UHDS, I/O Terminal, Fiat/Alfa IAW Bosch Decoder, UPA-USB, XPROG, FVDI, Orange5, Renolink, DiagBox, Can Clip, Xentry
-
The Following 2 Users Say Thank You to sl4ck For This Useful Post:
boris93600 (2nd May, 2018), CARPARTS (4th January, 2015)
-
4th January, 2015, 07:34 PM #6DK Veteran
- Join Date
- Jul 2010
- Posts
- 2,057
- Thanks
- 376
- Thanks
- 266
- Thanked in
- 143 Posts
hello
i have a same probleme whit the same car !!
i have repair by obd whit UHDS psa
have you the backup of the flash?you can repair by obd
regard
-
The Following User Says Thank You to newgeniehex For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 07:47 PM #7DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
Hi, here is the saved data from DP-3 / 992 kbyte (flash)
You need eeprom too ? (manual readout by removing eeprom)
You clearly see the area's where are '00' instead of data, comparing other fkashes from DP3....
-
The Following 5 Users Say Thank You to CARPARTS For This Useful Post:
Barajasz207 (22nd October, 2019), boris93600 (2nd May, 2018), canisha (31st October, 2017), sep382 (3rd August, 2020), willyboy28 (15th February, 2021)
-
4th January, 2015, 07:54 PM #8DK Veteran
- Join Date
- Jul 2010
- Posts
- 2,057
- Thanks
- 376
- Thanks
- 266
- Thanked in
- 143 Posts
hello
now you can use this backup but you must to use uhds tool psa
no need backupt of eeprom
after you have restore the bsi the car start direct!!!
can you put the sw of the bsi can you make a picture of the reference of the bsi please
regard
-
The Following 2 Users Say Thank You to newgeniehex For This Useful Post:
A630V (19th August, 2018), boris93600 (2nd May, 2018)
-
4th January, 2015, 08:01 PM #9DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
mmm, oke, but i dont have uhds tool
will bring car to PSA dealer and maybe online re-flash will work ??
-
The Following User Says Thank You to CARPARTS For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 08:07 PM #10DK Veteran
- Join Date
- Jul 2010
- Posts
- 2,057
- Thanks
- 376
- Thanks
- 266
- Thanked in
- 143 Posts
hello
psa dealer can not do repair by obd,sorry
have you try again to restore by obd to DP3
try to contact the support
regard
-
The Following User Says Thank You to newgeniehex For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 08:11 PM #11DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
Yes, i did try again
1/ DP3 does recognise only some parameters like HW version, and VIN, but VIN : "...." is not visible, although the VIN is cleary in 3 positions in eeprom.
2 DP3 ask new km
3/ DP3 start asking "ignition off & on", then wtart to write back this saved file, but arrived at 99%, stops writing and thats it..
Support on Sunday is difficult, will ask tomorrow morning.
-
The Following User Says Thank You to CARPARTS For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 08:18 PM #12DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
Other question ; IF i could find second-hand BSI, which number(s) on BSI-label should be the same as the original BSI-number(s) ???
-
The Following User Says Thank You to CARPARTS For This Useful Post:
boris93600 (2nd May, 2018)
-
4th January, 2015, 08:51 PM #13DK Veteran
- Join Date
- Jul 2010
- Posts
- 2,057
- Thanks
- 376
- Thanks
- 266
- Thanked in
- 143 Posts
hello
now i don' t have my dp3
in the menu bsi you don't have option write or restore the bsi?
regard
-
The Following User Says Thank You to newgeniehex For This Useful Post:
boris93600 (2nd May, 2018)
-
5th January, 2015, 09:20 AM #14DK Veteran
- Join Date
- Dec 2009
- Posts
- 1,298
- Thanks
- 111
- Thanks
- 1,197
- Thanked in
- 595 Posts
Your flash is corrupted.
Here you are good one (software signature 67.8A):
JCI_BSI_678A.rar
WBR, Marek
-
The Following 20 Users Say Thank You to tech_cz For This Useful Post:
A630V (19th August, 2018), boris93600 (2nd May, 2018), BusCan (30th October, 2019), ebor2k16 (11th June, 2024), garagecfa (30th January, 2020), garageozcar (24th April, 2018), gogoli (21st July, 2022), karri (23rd February, 2019), kronk92 (10th February, 2019), kumbari (6th December, 2017), mecafrigo (27th June, 2017), Neodim60 (9th March, 2023), pautri (13th November, 2017), pepe111 (15th December, 2017), pinokio383 (22nd October, 2017), pouettedu76 (22nd January, 2017), prodlt (2nd September, 2018), RomanDon (22nd August, 2018), wojtech (7th March, 2024)
-
5th January, 2015, 10:58 AM #15DK Veteran
- Join Date
- Nov 2011
- Posts
- 2,322
- Thanks
- 332
- Thanks
- 200
- Thanked in
- 132 Posts
Well, after all i managed to "repair" it as follow :
The flash dump as attached above "BSI_JC_FLASH_M00" is as i told before ; full of area's with "00", so its corrupted in my opinion.
Tech-cz also mentioned this.
Each time DP3 will try to restore, also as commanded in the log-file, the original flash.
But for some reason DP3 take all time the "BSI_JC_FLASH_M00" and stops at 99%.
In the MCC card/storage there is some other 992 kbyte flash with name "BSI_JC_FLASH_01" which is the +/- SAME as the attached flash from tech-cz.
This flash is the real original flash, and the "...M00" is the modified flash.
Now the trick is : change the name from the "01" flash into "M00" and the "M00" into "01".
Then DP3 will AGAIN try restore the flash with of course "M00", but this time the content is the good one because i "misleaded" DP3 by changing file-names
And indeed, this time until 100%, car start and you only need to re-do the whole procedure "read, verify, write" BUT THIS TIME WITH AN EXTRA BATTERY CHARGER.
Hope this will help some members with the same problem.
-
The Following 27 Users Say Thank You to CARPARTS For This Useful Post:
A630V (19th August, 2018), Aliazadar (14th March, 2018), boris93600 (2nd May, 2018), BusCan (30th October, 2019), clauberty (15th March, 2015), ebor2k16 (11th June, 2024), Faraday (29th March, 2015), gabrielandriev (16th September, 2018), gogoli (21st July, 2022), jackeldestripador (14th November, 2017), javiere (27th November, 2017), javyb (5th January, 2015), junmab (5th January, 2017), kelekele (15th March, 2015), kronk92 (6th February, 2017), lion0304 (20th April, 2015), makadam (8th December, 2019), MERCO86 (5th January, 2015), Prestigeauto (6th May, 2018), Recoder (16th March, 2015), sendreq (22nd November, 2016), Speedofix (16th March, 2015), taxo1965 (12th October, 2017), tor2lehel (8th July, 2015), tziku (5th January, 2015), urcarpc (13th January, 2015), xifly18 (2nd April, 2018)
Reply With Quote
Bookmarks