VVDI PROG

[gilahish]

Have a problem, kinda weird question i hope someone can help me understand what i do wrong. today was second Range Rover CEM i tried to read (09 range sport), first one few weeks ago had the same problem but in the end i made it. today i did the same thing, took resistor out, connected all the cables but when i got to the GND i couldn't solder it to board what so ever, tried for almost an hour. can anyone point at something i do wrong? put flux on board, cables and solder head, all the other cables were just fine except this one.
thanks in advance

Screen Shot 2017-04-26 at 00.29.52.jpg

[electromech]

Have a problem, kinda weird question i hope someone can help me understand what i do wrong. today was second Range Rover CEM i tried to read (09 range sport), first one few weeks ago had the same problem but in the end i made it. today i did the same thing, took resistor out, connected all the cables but when i got to the GND i couldn't solder it to board what so ever, tried for almost an hour. can anyone point at something i do wrong? put flux on board, cables and solder head, all the other cables were just fine except this one.
thanks in advance

Screen Shot 2017-04-26 at 00.29.52.jpg

Its the Ground....you need more powerful Iron as the ground absorbs alot of heat from small Iron

Let me know if you can read these with VVDIPROG as I cant seem to get pass security

[gilahish]

Its the Ground....you need more powerful Iron as the ground absorbs alot of heat from small Iron

Let me know if you can read these with VVDIPROG as I can seem to get pass security

i already did, i even wrote it in here few weeks ago.. didnt have much of a luck yesterday..

[Nathansauto01]

Hello the way i do it is i take my multimeter and use it in ohm setting to find another ground and it works perfect ill see if i have a saved picture for you

[gilahish]

Hello the way i do it is i take my multimeter and use it in ohm setting to find another ground and it works perfect ill see if i have a saved picture for you

Ok that sounds interesting, and basically how can i do it? What do i need to see in multimeter?

[Maartinj]

Ok that sounds interesting, and basically how can i do it? What do i need to see in multimeter?

You can find a capacitor + - and solder to the - , also transistor with GND. ANy GND is good

[smartkeyprogs]

Hello!

I want to know," V4.5.7 Xhorse VVDI PROG Programmer " can read and write " UPD70F3570 " from V850E2 ?

[wojtass]

Hi,
What can i do vvdi2 basic?
What is the authorization?

[rob h]

Hi,
What can i do vvdi2 basic?
What is the authorization?

This thread is about vvdi2 prog, not vvdi2!

[smartkeyprogs]

This thread is about vvdi2 prog, not vvdi2!

Hi,

I want to know," V4.5.7 Xhorse VVDI PROG Programmer " can read and write " UPD70F3570 " from V850E2 ?

[Astronom]

Hi all. My VVDI_PROG can't erase D80 and D160

https://www.youtube.com/watch?v=c1zmVkYdwVg

[offsystem]

Vvdi cant set lockbit for readprotection of NEc 3426

[offsystem]

Vvdi cant set lockbit for readprotection of NEc 3426

How can i contact tech support for this issue?

[CarCity]

Hi all
VVDI Prog not connect in XC2363B-40
All wire is ok connect
Any idea please ?!


Sent from my iPhone using Tapatalk

[CarCity]

So
XC2361B-40
All wire is ok connect
and vvdi prog not connect to chip
Where is my hitch ??



Sent from my iPhone using Tapatalk