Zgemma 2s OpenAtv 5.2 Backup Image with Improved $ky Skin

[martin035]

Thanks Martin. All sorted bar channel 5. Is there no SD equivalent?

Yes there is a channel 5 SD the only thing I can think of is to ensure Menu-setup-service searching-abm-providers-sky UK:swap channels is set to yes, if its set to no then Change it and rescan abm

[TheStretchedElf]

Yes there is a channel 5 SD the only thing I can think of is to ensure Menu-setup-service searching-abm-providers-sky UK:swap channels is set to yes, if its set to no then Change it and rescan abm

Hmm, that was set correctly. It's a mystery. Never mind, it's only channel 5 . Thanks for all the help mate!

[cityboy]

Hello

I have just purchased the above box and I am trying to flash with this image, but everytime i try and flash it when the box continues to boot. I think I have followed the steps on here correctly but had no luck

I have used 3 different memory sticks one being a 32gb kingston data traveller formatted with hddguru, then windows format, extracted to the USB still no joy.

Does anyone have any ideas that can help.

Thanks in advance

[cityboy]

Hi can someone help with loading this image using ftp.

thanks

[martin035]

Hello

I have just purchased the above box and I am trying to flash with this image, but everytime i try and flash it when the box continues to boot. I think I have followed the steps on here correctly but had no luck

I have used 3 different memory sticks one being a 32gb kingston data traveller formatted with hddguru, then windows format, extracted to the USB still no joy.

Does anyone have any ideas that can help.

Thanks in advance

I've just tried to flash the image via USB and it flashes ok, so it seems to be that your Zgemma doesn't like your USB drives, I assume your have the USB in the rear port and on boot 'USB' isn't displayed on the front LCD screen.

Right, you could try this, it may work. This will only work if the factory default Openatv image is on the Zgemma.
A. Boot the Zgemma and carry out the post Initial boot up setup if required
Post Flash Initial Setup–( Use remote scroll left right up and down arrows as required)
System boots in German, don’t worry we’ll change that soon
1. Select your TV connectiom type ie HDMI press Ok
2. Select your TV resolution ie 1080i press Ok
3. Select your Refresh rate ie 50mhz press Ok
4. Select ‘English UK’ press Ok
5. Press Ok at the User Interface setup
6. Press Ok to use 'Wizard for Basic'
7. Select 'Check Internet Connection'
8. Press Ok if Internet working
9. Setup Tuner A - Config mode scroll to 'Simple' , Satellite scroll to '28'2e Astra' ,Send DISCqC to 'Yes' leave all other options default, Press Ok
10. Setup Tuner B - Config Mode 'equal to' Press Ok
11. 'No scan Later' press Ok
12. Network setup Press Ok, Press Ok again
13. Press ‘Exit’ again when shown the German channel Bouquets
B. Plug in your USB drive into the front USB port
C. on the Remote menu-setup-software management-flash online/local then press Yellow and yellow again
D. Find your USB drive in the list and enter each folder until you find 'rootfs' file
E. Scroll to the 'rootfs' file and press Green

The zgemma will then flash the image, when the zgemma reboots remove the front USB and insert your Storage USB into the rear and continue with instructions from setting up the USB hard drive.

[cityboy]

I've just tried to flash the image via USB and it flashes ok, so it seems to be that your Zgemma doesn't like your USB drives, I assume your have the USB in the rear port and on boot 'USB' isn't displayed on the front LCD screen.

Right, you could try this, it may work. This will only work if the factory default Openatv image is on the Zgemma.
A. Boot the Zgemma and carry out the post Initial boot up setup if required
Post Flash Initial Setup?( Use remote scroll left right up and down arrows as required)
System boots in German, don?t worry we?ll change that soon
1. Select your TV connectiom type ie HDMI press Ok
2. Select your TV resolution ie 1080i press Ok
3. Select your Refresh rate ie 50mhz press Ok
4. Select ?English UK? press Ok
5. Press Ok at the User Interface setup
6. Press Ok to use 'Wizard for Basic'
7. Select 'Check Internet Connection'
8. Press Ok if Internet working
9. Setup Tuner A - Config mode scroll to 'Simple' , Satellite scroll to '28'2e Astra' ,Send DISCqC to 'Yes' leave all other options default, Press Ok
10. Setup Tuner B - Config Mode 'equal to' Press Ok
11. 'No scan Later' press Ok
12. Network setup Press Ok, Press Ok again
13. Press ?Exit? again when shown the German channel Bouquets
B. Plug in your USB drive into the front USB port
C. on the Remote menu-setup-software management-flash online/local then press Yellow and yellow again
D. Find your USB drive in the list and enter each folder until you find 'rootfs' file
E. Scroll to the 'rootfs' file and press Green

The zgemma will then flash the image, when the zgemma reboots remove the front USB and insert your Storage USB into the rear and continue with instructions from setting up the USB hard drive.

Fantastic that worked a treat. Thanks for your help

[martin035]

Fantastic that worked a treat. Thanks for your help

Thanks for letting us know, that will help a lot of people who have troublesome USB stick drives.

[casper100]

Hi i followed all the instructions but when setting up EPG it lets me download and update but IN EPG settings/location i can't change it from internal flash can anyone help

[martin035]

Hi i followed all the instructions but when setting up EPG it lets me download and update but IN EPG settings/location i can't change it from internal flash can anyone help

What does it say under Detected Devices (menu-Information-Devices)

Also I find changing the Epg location can be slow to respond, ensure that the spinning wheel stops then press the right scroll button.

[casper100]

device is detected and i have waited but it won't change when i first downloaded the cross epg i changed it it flash disk no problem but epg location still says internal flash

[martin035]

device is detected and i have waited but it won't change when i first downloaded the cross epg i changed it it flash disk no problem but epg location still says internal flash

Sorry, not to get back to you quicker had to re install the image to find the fault/bug, anyway try this;

1. Re-initialise your USB flash drive: Menu-setup-system-storage devices-Initialisation and select your drive
2. Re-setup your swap file: Menu-info Panel-Plugins- Swap Manager, Blue to create 256mb, Green to activate, yellow to autostart
3. Reboot

Go into Menu-Setup-EPG-settings and hopefully the location is now '/media/hdd' press red to exit

Redownload 'Crossepg' and Save 'EPG' by:
1. Ensure Menu-Setup-Crossepg-Config ‘storage location’ is correct, if says ‘internal’ change to ‘your usb drive name’
2. Menu-Setup-Crossepg-Download Now and let the epg update
3. Menu-Setup-EPG-load/save – save EPG

[casper100]

followed your instructions but still on internal flash yet when i reloaded cross epg it was on usb

[martin035]

followed your instructions but still on internal flash yet when i reloaded cross epg it was on usb

So Crossepg saves to your USB but the EPG says 'internal' and won't scroll? Try another Full Reboot and see if it will scroll, if it doesn't have you got another USB flash drive to try?

[casper100]

When I reboot it doesn't find USB stick will have to try another one

[3pinplug]

Cheers. All set-up on a H1 using cable and sat...Great image, very stable...