I have a clon 2014. Vectra c 2003 z20net no Read pin Code. Have anyone this problem?
Wysłane z mojego SM-G390F przy użyciu Tapatalka
I have a clon 2014. Vectra c 2003 z20net no Read pin Code. Have anyone this problem?
Wysłane z mojego SM-G390F przy użyciu Tapatalka
Last edited by wbart; 11th February, 2018 at 07:51 PM.
I would like to buy FVDI Clone. Which version to choose? 2014 or 2015?
I need to add a new key using FVDI2 to a VW Gol 1.0 with the following data
Address 01: Engine
Part No: 030 906 034 T
Component: MARELLI 4BV MPSF 1261
Address 17: Instruments
Part No: 5X0 920 827
Component: 22-KOMBIINSTR. M73 V01
I can not find any way to read the box (K-Line) to get the PIN-CODE.
Any suggestions
Thank you so much
Last edited by eltoke; 18th February, 2018 at 09:30 AM.
In a 2014 Audi A4 B8 and 2014 Audi A6 to add a second key with a key that works properly with the car. It is mandatory to read the BCM2 through a programmer (Orange5) or it is possible to do everything using only the FVDI2 without the help of a programmer external?
Audi A4
Hardware part number: 8K0907064FQ
Hardware version number: H11
Software version number: 0621
Designation of the system: BCM2 2.0
Last edited by eltoke; 3rd March, 2018 at 05:33 AM.
Maybe this question is silly but I prefer to be cautious.
The black cable that comes with the FVDI2 adapter is for connecting an external 12V power supply. Whenever an ECU (MED17, etc) is to be read, it is necessary to feed this cable with an external 12V source
Attached image of the cable.
Thank you
Col19 (10th January, 2021)
I wanted to thank this forum and especially this thread that gives us the possibility to clarify many of our doubts with this tool.
Greetings from a country where there is no Avdi, FVDI, dealers and very little internet, where you try not to make mistakes because if you make a mistake you stayed without car.
As I see in this post there is a manual for the FVDI2, where can you get this manual?
One of the things that most work has given me is to find information on how to proceed in each case and as published here there is a manual or a guide.
Example
Engine Control Unit: Detail can be found in chapter 6.1 engine control unit
K-Line Instrument/Immobox: Detail can be found in chapter 6.2 K-Line instrument/immobox
Change KM: Detail can be found in chapter 6.3 change KM
Can FVDI clone read write eeprom flash Volvo v70 2003?
Thanks
Anyone help with key learning on Porsche 9x6 returning 'Learning Failed' - can run the key learning program successfully and see the current keys written to each slot but not write a new key without the 'learning failed' error. Do I need to write the alarm eeprom with the modified dump under the option 'enable access to alarm module by OBDII'? Not sure this should be necessary as PIWIS can do it without. Or can anyone tell me how to write a key to the binary dump directly? Thanks in advance for any help!
Some of the function are working but some of them not
Any word on Range Rover?
Sent from my SM-G930F using Tapatalk
Hi
i have fvdi clone 2014 , I get error message when I start up fvdi "file corrupted this program has been manipulated and maybe it's infected by a virus or cracked"
if I reinstall software all is OK, but later again same error, can someone help me please ?
Need I to disconnect internet ?
dont have antivirus, use XP pro , no other soft are installed on laptop,,I use it just for FVDI
Bookmarks