CARPROG 8.21 INFO IN HEX - Page 2
Register
Page 2 of 4 FirstFirst 1234 LastLast
Results 16 to 30 of 54
  1. #16
    DK Veteran

    Join Date
    Sep 2013
    Location
    garage
    Posts
    1,545
    Thanks Thanks Given 
    334
    Thanks Thanks Received 
    646
    Thanked in
    464 Posts

    Default

    someone try to program mcu at91sam7s256 with samba ...?

  2. #17
    Top Poster +
    Join Date
    Apr 2014
    Posts
    218
    Thanks Thanks Given 
    98
    Thanks Thanks Received 
    180
    Thanked in
    69 Posts

    Default

    here you go mate...it should work.

    Pass in PM.
    Attached Files Attached Files

  3. The Following 8 Users Say Thank You to Shemek For This Useful Post:

    ADEL.KSHLAF (23rd January, 2018), andre1234567890 (14th November, 2018), azare (15th December, 2016), DieselManiac (27th February, 2017), drpeter (8th October, 2016), gregrimaster (15th October, 2017), mohammed s moha (2nd April, 2020), toha (3rd January, 2017)

  4. #18
    Top Poster +
    Join Date
    Apr 2014
    Posts
    218
    Thanks Thanks Given 
    98
    Thanks Thanks Received 
    180
    Thanked in
    69 Posts

    Default

    Mr BLACK the answer for UR question is yes but same SW versions of SAMBA has few bugs and you might end up with "device not recognised" after programming and using for a while your CarProg so better to use J-Flash for segger .

  5. The Following User Says Thank You to Shemek For This Useful Post:

    Mr BLACK (10th October, 2016)

  6. #19
    Top Poster
    Join Date
    Jun 2010
    Posts
    133
    Thanks Thanks Given 
    48
    Thanks Thanks Received 
    9
    Thanked in
    7 Posts

    Default

    Quote Originally Posted by Shemek View Post
    here you go mate...it should work.

    Pass in PM.
    may i have a pass too please ? have the same problem , thanks

  7. #20
    DK Veteran
    pike's Avatar
    Join Date
    Sep 2013
    Posts
    2,710
    Thanks Thanks Given 
    1,821
    Thanks Thanks Received 
    1,565
    Thanked in
    995 Posts

    Default 150428CAR00542UA.lib

    Lib file 150428CAR00542UA

  8. The Following 11 Users Say Thank You to pike For This Useful Post:

    bokilee (20th October, 2016), brodaty (12th October, 2016), habbou (24th February, 2017), Hazzard (12th October, 2016), iahim (12th November, 2016), macako6 (8th November, 2016), mitch2 (1st January, 2017), patiomkin11 (26th March, 2017), semga (10th October, 2016), shirokov (9th October, 2016), tiomilo (8th October, 2016)

  9. #21
    Newbie
    Join Date
    Oct 2016
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Sory to bother but i wantet to ask what do you gays think about carprog 9.31 chines clone and the SBB silca key progamer.

  10. #22
    V.I.P. Member
    drpeter's Avatar
    Join Date
    Dec 2009
    Location
    The Netherlands
    Posts
    5,129
    Thanks Thanks Given 
    537
    Thanks Thanks Received 
    2,339
    Thanked in
    1,189 Posts

    Default

    Quote Originally Posted by igor1110 View Post
    Sory to bother but i wantet to ask what do you gays think about carprog 9.31 chines clone and the SBB silca key progamer.
    Gays? I tested the 8.21 clone on a VW UP 2012, the software connected to CAN got security acces reads the dash part no but then stops. Is it the A1 cable or the soft? KIA Sportage by obd works fine. I also tired to read/write a EWS3, but the cable 11 wiring isn't right, i have to look at it.

  11. #23
    Newbie
    Join Date
    Sep 2016
    Posts
    3
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    hello please give me pass code

  12. #24
    Top Poster +
    Join Date
    Apr 2014
    Posts
    218
    Thanks Thanks Given 
    98
    Thanks Thanks Received 
    180
    Thanked in
    69 Posts

    Default

    try to replace mcp2515 for good one...
    ews3-why dont you use adopter A11 ews to read and write this module..?it works ok but Chinese one has bad wiring so you need to do a bit of modification...

  13. #25
    Top Poster +
    Join Date
    Apr 2014
    Posts
    218
    Thanks Thanks Given 
    98
    Thanks Thanks Received 
    180
    Thanked in
    69 Posts

    Default

    wasil37vc
    you got it now...right?

  14. #26
    Senior Member
    Join Date
    Mar 2010
    Location
    Portugal
    Posts
    257
    Thanks Thanks Given 
    91
    Thanks Thanks Received 
    38
    Thanked in
    23 Posts

    Default

    Quote Originally Posted by drpeter View Post
    Gays? I tested the 8.21 clone on a VW UP 2012, the software connected to CAN got security acces reads the dash part no but then stops. Is it the A1 cable or the soft? KIA Sportage by obd works fine. I also tired to read/write a EWS3, but the cable 11 wiring isn't right, i have to look at it.
    Greetings Dr. peter did you make the hardware test for the A1 cable. For the A11 here's schematic from Codecard for you to check. I think you should resolder the carprog base programmer if it is a clone it as very bad soldering and check capacitors polarity.
    Attached Images Attached Images

  15. The Following 3 Users Say Thank You to JotaB For This Useful Post:

    clico70 (16th August, 2017), drpeter (21st November, 2016), iahim (12th November, 2016)

  16. #27
    DK Veteran
    digi men's Avatar
    Join Date
    Nov 2013
    Location
    EU
    Posts
    391
    Thanks Thanks Given 
    45
    Thanks Thanks Received 
    159
    Thanked in
    107 Posts

    Default

    Hy,i need some help .
    i bought a carprog from china, cd is corupt and i need sw and activating for it, on lable is 8.21 -8.09 ,
    or if is good wat you give to drpeter ? Can i have the pass for it than .

    Thanks in advance
    Stop worrying about what can go wrong, and get excited about what can go right.

    PRESS THANKS IF YOU LIKE MY POST AND IT HELPED YOU




  17. The Following 3 Users Say Thank You to digi men For This Useful Post:

    iahim (12th November, 2016), mikroel (29th October, 2016), ozuque (29th October, 2016)

  18. #28
    Newbie
    Join Date
    Nov 2016
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    081105CAR001773I plz

  19. #29
    Senior Member
    Join Date
    Mar 2009
    Location
    Europe
    Posts
    255
    Thanks Thanks Given 
    110
    Thanks Thanks Received 
    32
    Thanked in
    17 Posts

    Default

    here is lib
    Attached Files Attached Files

  20. The Following User Says Thank You to maki For This Useful Post:

    macako6 (8th November, 2016)

  21. #30
    DK Veteran

    Join Date
    Jul 2013
    Posts
    4,100
    Thanks Thanks Given 
    3,385
    Thanks Thanks Received 
    8,575
    Thanked in
    2,987 Posts

    Default 8.21 lib

    her is lib
    Attached Files Attached Files

  22. The Following 2 Users Say Thank You to petronijul For This Useful Post:

    bhpmotorsport (3rd September, 2018), kebappa (3rd November, 2018)

 

 
Page 2 of 4 FirstFirst 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.