>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

[PremierD]

Ok I have a SX9 Key
the cuts on the top edge (as opposed to the side edge) have little cuts in them... (think half moon)
whilst the original key has a long low cut into it... in theory it should work, if depths are right...
But it doesn't work! And it wont decode either... Is there update soon Samic.

Mc

TOP of page ...

Hello, I need help I have mini condor key machine, and can't work with M3 clamp, can't decode or cut any SX9 key. Need any additional configuration for use this clamp? Thanks



M3 clamp not need calibration,directly use.it cannot decode key,shoud enter bittings by manual then cutting.if still cannot work let me check for you.

[wd bau]

hi
i have never succeed to cut buy code or copy HYUNDAI / KIA HYN14R or HYN14 profile every time there different between Right and left side. i hope can rectify this .

[CaioW]

Little tip for all users.

I have machine with SN starting with KM02.

To cut keys HU92 BMW need to be in 1.00MM, when you select HU92 the device will ask you to chose between Land ravor and BMW, Land Rover came with 1.00mm and BMW with 1.25mm, if you try to cut with 1.25mm the key will not turn.

I have proved with 4 different machines and 3 different cars.

[Nassreddine84]

Hi need help update the car data base in this software all cars are 0 how can i import the key info for each car

[amigokola]

Guy's long time not much feedback from you ???? I think about buying XC-mini. Is it bug fixed yet ??

[daxxer]

I haven't no any problems with Condor XC-Mini
cut keys blade HU64-3 without any problems in first attempt

[purdy]

Just got a new mini. So very new to this. Been very successful up till now. Tried to decode a Renault megane emergency key Card type. Renault-megane-2003- Condor checks the clamp position ok then goes looking for the tip of the key but misses the tip with the prob going down the middle of the cut for 5mm then backs off as it thinks no key is in the clamp. Is it operator error or a bug. Look like the probe is not low enough to bump into the key tip. Other than this I'm very happy.


Sent from my iPad using Tapatalk

[paul_12345]

Just got a new mini. So very new to this. Been very successful up till now. Tried to decode a Renault megane emergency key Card type. Renault-megane-2003- Condor checks the clamp position ok then goes looking for the tip of the key but misses the tip with the prob going down the middle of the cut for 5mm then backs off as it thinks no key is in the clamp. Is it operator error or a bug. Look like the probe is not low enough to bump into the key tip. Other than this I'm very happy.


Sent from my iPad using Tapatalk

its probably not the probe being low enough but your key thats not high enough! these blades need spacers (unless the clamps are different on the mini)

The reason is because although the top of the blade clears the clamp the cutter will be lower and would hit the clamp whilst cutting the tip of the key.

[hbt]

I also have this problem with megane key . The key is located to low sow condor cannot find the key and does give a error how to solve this problem guys?

[paul_12345]

I also have this problem with megane key . The key is located to low sow condor cannot find the key and does give a error how to solve this problem guys?

Can you not see my post above yours - Use a spacer / shim !!!

[Samic]

hi
i have never succeed to cut buy code or copy HYUNDAI / KIA HYN14R or HYN14 profile every time there different between Right and left side. i hope can rectify this .

HYN14 or HYN14R should work ok if your machine calibration ok,M1 clamp better use 1.5mm cutter.
if your machine still not work well,let me check the detailed parameters for you.

[Samic]

[QUOTE=Nassreddine84;2859528]Hi need help update the car data base in this software all cars are 0 how can i import the key info for each car /QUOTE]

mate,this function for customer define key that the key without any detailed information currently.each key data need to measure by yourself.
the attachment file is sample about define key,mainly Chinese vehicles.(extract the file,'Import' to key data customize tool software)

[jester71354]

Cool

Sent from my SAMSUNG-SM-G930A using Tapatalk

[Samic]

Guy's long time not much feedback from you ???? I think about buying XC-mini. Is it bug fixed yet ??

HU64 update to latest version should be ok,fixed this issue already.about HU56R 3.5mm keys still finding another solution.

[Samic]

Xhorse Condor XC-Mini video download link(include how to calibrate & how to use M3 clamp cutting keys)
if your machine still not work well/find bugs/good advise,please post here/PM me.