>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

**purdy** · 20th October, 2016, 11:54 PM

Originally Posted by paul_12345

its probably not the probe being low enough but your key thats not high enough! these blades need spacers (unless the clamps are different on the mini)

The reason is because although the top of the blade clears the clamp the cutter will be lower and would hit the clamp whilst cutting the tip of the key.

Had a bash today. There is a small lip on the right side of the clamp. If the key is clamped under this lip it reads is perfect. Same effect as shimming.

Sent from my iPad using Tapatalk

**purdy** · 9th November, 2016, 02:59 PM

Hi all
need to do SX9 keys were to buy clamp
will it decode these too
Samic can't find anyone with stock. There seems to be confusion with the New M3 clamp. Can you. Clarify please

**neverquiet** · 13th November, 2016, 05:10 AM

Will condor mini be supported by instacode in any near future?
I hope I can use it to make kwikset master keys generated by instacode.

BR

**CaioW** · 14th November, 2016, 02:44 PM

Originally Posted by purdy

Just got a new mini. So very new to this. Been very successful up till now. Tried to decode a Renault megane emergency key Card type. Renault-megane-2003- Condor checks the clamp position ok then goes looking for the tip of the key but misses the tip with the prob going down the middle of the cut for 5mm then backs off as it thinks no key is in the clamp. Is it operator error or a bug. Look like the probe is not low enough to bump into the key tip. Other than this I'm very happy.

Sent from my iPad using Tapatalk

There is an adapter to make renault card emergy keys.. Its a piece of steel who have the correct high.. just put above the key.. you can read and cut perfectly.

Originally Posted by neverquiet

Will condor mini be supported by instacode in any near future?
I hope I can use it to make kwikset master keys generated by instacode.

BR

MiniCondor have instacode inside.. you can put your code and prove if the code is true or not.. or even if you dont have some cuts device will search all the posibles cut for you.

**MaxMin** · 14th November, 2016, 04:34 PM

can condor cut key if i received Mechnical Code from PSA server ?

**daxxer** · 15th November, 2016, 08:09 AM

Originally Posted by MaxMin

can condor cut key if i received Mechnical Code from PSA server ?

if you have key code can Condor support on key database function

**purdy** · 21st November, 2016, 07:23 PM

hi all
whats the latest soft for the condor mini im on 3.0.1?

**PremierD** · 21st November, 2016, 08:16 PM

that is the latest ....

**jaelgti** · 24th November, 2016, 10:07 AM

Greetings, friends, can you put it in Spanish?
Thank you

**obeids** · 29th November, 2016, 06:16 AM

Hi there Guys.

I am having a problem with my Condor Mini.
I was trying to cut a Hyundai Accent Key with HY18R / HY18. After decoding the Screen would become white and the machine wouldn't do anything.
So I figured they might have an update for the machine.
I tried updating and it kept saying COMMUNICATION WITH SERVER FAILED (5).
Problem is now my machine is stuck on the bootup screen and I cannot use the machine.

Any solutions guys?

**CaioW** · 1st December, 2016, 03:32 PM

Originally Posted by jaelgti

Greetings, friends, can you put it in Spanish?
Thank you

Actualy there is an update with Spanish version, but the translation is bad.. have tested and dont work very well.

**jaelgti** · 2nd December, 2016, 09:07 AM

[Quote = CaioW; 2902052]. Actualy hay una actualizaci?n de la versi?n espa?ola, pero la traducci?n es mala .. han probado y no funcionan muy bien [/ quote]

Thank you very much
The truth is that not necessary, it is a very intuitive machine
I'm very happy with the machine
regards

**rob h** · 3rd December, 2016, 01:09 AM

Will there be a clamp for keys, other then automotive?
Creating a new key in the database is possible with the update software.
But the clamps are limiting some cutting depths.
It would be great if i could use the machine for tubular key cutting, and some house Keys.

I am very happy with the master cutter!
Great tool, with potential!