>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

[paul_12345]

http://key-code.com/es/accesorios-de...lt-condor.html

http://key-code.com/es/accesorios-de...lt-condor.html


This ones

Just need any metal shim about 0.5mm but that does not appear to be the issue with the mini.

[rob h]

I have a problem with my condor master, 1484755689557-403239711.jpg
The machine does not react to anything.
Calibration is written on the screen, and a + sign in the legt corner.
Pressing the + short or long does not help.
I updated the device online, hoping it would fix things.
I tried fix data error, and even fix internal error 1 and 2.
How can i fix this!

[gokart]

It looks like a touch screen calibration. Try to touch sign + with a touch screen pen which has smaller surface than your fingers.

[rob h]

Thanks Gokart, I have tried this,
At one time the plus turned blue, and a next one appeared.
SO i press that one, turning it blue.
The thirth + appeared, but turn blue itself with out waiting for me to press it.
So did the fourth and the one in the center.
Then it started allover with a single white + in the left uppper corner.
And it stopped reacting to my touch, even with or without screen pen.
It is inside the garage, so i wonder if it could be a temperature issue.

[gokart]

Maybe low or high temperature causes this problem. Try to make again the calibration. If you touch it incorrectly maybe the calibration fails then starts again. I have another tool with touchscreen which has similar calibration. The big question is why are you seeing this screen. I hope you can solve it only with touching the sign +.

[rob h]

Thanks, i will place the machine inside tommorow.
I whas typing in the key cuts, and then the machine came up with this calibration screen!

[paul_12345]

Thanks Gokart, I have tried this,
At one time the plus turned blue, and a next one appeared.
SO i press that one, turning it blue.
The thirth + appeared, but turn blue itself with out waiting for me to press it.
So did the fourth and the one in the center.
Then it started allover with a single white + in the left uppper corner.
And it stopped reacting to my touch, even with or without screen pen.
It is inside the garage, so i wonder if it could be a temperature issue.

sounds like the touchscreen is registering random presses... could be the touchscreen is going faulty.

I would try getting a hair dryer and gently warming the screen even to make sure moisture is not causing a issue.

else remove the screen from the case and press around the edge in a certain place and try the touchscreen or even pack around the screen with paper or something to put pressure around the edge.

if you find a spot thats delaminating you can put some high temp tape over and use a soldering iron to slightly melt it, or soldering iron with lcd ribbon repair tip.

[CaioW]

Just need any metal shim about 0.5mm but that does not appear to be the issue with the mini.

Its a known issue, this is why this adapters exists..

[rob h]

The machine is inside, where it is nicely warm.
And the machine is getting out of the calibration mode quicker.
But Every time i send a command by USB, is goes to calibration mode.
I remove the 3 custom Keys, and reset everything.
Reloaded latest v2.3.3 again.
But still it is slipping in to calibration mode after any USB command, and sometimes after just turning the machine on.
Xhorse support is not pitching in yet!
So i will try to skype condor_keymachine@hotmail.com

[AndyCZ]

Tried custom key for Megane/Scenic card with no luck.


Samic is it possible fix it with next update?

[paul_12345]

Tried custom key for Megane/Scenic card with no luck.


Samic is it possible fix it with next update?

what was wrong with the custom one??

[AndyCZ]

what was wrong with the custom one??

check first picture, check next picture.

[paul_12345]

check first picture, check next picture.

Post the details of the custom key you added

[AndyCZ]

Post the details of the custom key you added

here is the key I created. I tried many version but no luck.
It cannot decode according it right.

[paul_12345]

here is the key I created. I tried many version but no luck.
It cannot decode according it right.

can't open your file... but had another look at the pics and you've entered the cut depths backward