>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

[cqae]

Better start using the silca platform. HYN17

hyn17 isnt on my old condor, is it on the mini?

Ill probably have to upgrade soon, and am tossing up if I should get a mini or look at a miracle or bianchi, any suggestions?

[rob h]

HY21R HY18R.jpgHY21U choose HY18R

Stick to the master, it can do these just fine!

hyn17 isnt on my old condor, is it on the mini?

Ill probably have to upgrade soon, and am tossing up if I should get a mini or look at a miracle or bianchi, any suggestions?

[cqae]

thanks Rob, ur a legend! Ill try that

Aweosme mate, just cut it & all good, I was sure I searched all of them, but obviously I didnt, thanks so much!

[obeids]

Attachment 505036Attachment 505037
thats what i have picture
tryed lot of times and didnt worked

These are VA2 profile. Cut it with VA2 and not VA6.
I did one just the other day and worked perfect.....

[wissamshaat]

These are VA2 profile. Cut it with VA2 and not VA6.
I did one just the other day and worked perfect.....

there is no va6 profile in machine
tried the va2 profile both numbers and letters and it dont works
peugeot va2 blades work good

[kronk92]

I tried to cut FO21 but it doesn't cut it well, there is some spacing , this photo is cut with 412443
IMG_20180220_142831.jpg

[kleidaras]

you dont have put key ok on clump

[kronk92]

IMG_20180220_190635.jpg
This is the maximum that i can do

[cniksor]

not sure if the instacode got updated but again if i enter a key code im getting two different options, even when i put in year and make and model i still get two key cuts
ha00005942 2006 bmw 530

i took a guess and got it right but i cant keep guessing.

am i going to a wrong setting?

[sleepyrz]

IMG_20180220_190635.jpg
This is the maximum that i can do

adjust the screw in the back

and tap back of key with plastic hammer like bump hammer to make sure it is fully seated against stop

[kronk92]

thank you guys, i did hammer the key to fully enter and now it cuts well !

[rob h]

not sure if the instacode got updated but again if i enter a key code im getting two different options, even when i put in year and make and model i still get two key cuts
ha00005942 2006 bmw 530

i took a guess and got it right but i cant keep guessing.

am i going to a wrong setting?

Consider using a lishi decoder.
The direct reader might be enough to select the correct one.

[sleepyrz]

not sure if the instacode got updated but again if i enter a key code im getting two different options, even when i put in year and make and model i still get two key cuts
ha00005942 2006 bmw 530

i took a guess and got it right but i cant keep guessing.

am i going to a wrong setting?

no they have added many new cards to the system

they even have cards for the new m4 clamp that has not even come out yet

check gm26r if you want to see the m4 clamp setup


they are adding many new things and making it more capable

but it is making it hard for the people that dont know the intricate little details on how to determine what card to use

i am slowly learning how to figure it out case by case

[sleepyrz]

hu100 10 cut is wrong still..........

cuts too far to the left


good thing i made a custom key file for it


how is it im able to get it right on the first try having never used their software before and they still cant get it right and they wrote the damn thing....................

[fytfh]

Hi i have to cut key by pictures but doing some wrong i decode key by eyes 13231222 but not work on the car