>>>>>>>>SMOK SUPPORT THREAD<<<<<<<

[okaj28]

post vin, i can tell you all info from vin

[okaj28]

Are you trying to correct dash only out of car?

Sent from my SM-N960F using Tapatalk

no, i think when i make it on table and then put back to car, then will be the same i think

[javyb]

no, i think when i make it on table and then put back to car, then will be the same i think

U need to use the option in below pic.

Sent from my SM-N960F using Tapatalk

[okaj28]

yes, i use this option and nothing..

[javyb]

yes, i use this option and nothing..

Did u try the 2013 option?

Sent from my SM-N960F using Tapatalk

[amigokola]

Lately tried to swap A4 RB8 dashboard and after copy SB DEF on lcd. Tried another time and DEF again.
Blamed the tool and think maybe after last update something is wrong but no....
Tool works well but there are two types of RB8 clusters: 7 byte CS and 12 byte CS
If SB editor would work we could see it....
Always save original eeprom Guys. This saved me in this case.
PS: Is there a possibility to adapt 12byteCS dash to 7byte system without immo off and new transponders ??

[okaj28]

Did u try the 2013 option?

Sent from my SM-N960F using Tapatalk

yes, and init error

[Manuelgb]

Lately tried to swap A4 RB8 dashboard and after copy SB DEF on lcd. Tried another time and DEF again.
Blamed the tool and think maybe after last update something is wrong but no....
Tool works well but there are two types of RB8 clusters: 7 byte CS and 12 byte CS
If SB editor would work we could see it....
Always save original eeprom Guys. This saved me in this case.
PS: Is there a possibility to adapt 12byteCS dash to 7byte system without immo off and new transponders ??

I think smok does not work well on these board with cs. The cs editor does not read well

[javyb]

Anybody any experience with licence
MS0008 Mercedes W251, W164, X164 EZS KM
For the NEC Havana ezs. Does it work

Thanks

Sent from my SM-N960F using Tapatalk

[qeso705]

Lately tried to swap A4 RB8 dashboard and after copy SB DEF on lcd. Tried another time and DEF again.
Blamed the tool and think maybe after last update something is wrong but no....
Tool works well but there are two types of RB8 clusters: 7 byte CS and 12 byte CS
If SB editor would work we could see it....
Always save original eeprom Guys. This saved me in this case.
PS: Is there a possibility to adapt 12byteCS dash to 7byte system without immo off and new transponders ??

It isn't possible. They used old ecus without Immo4 on cars where they put immo3 rb8. 2.5TDI and 1.8T are these cases.

[peko]

Anybody any experience with licence
MS0008 Mercedes W251, W164, X164 EZS KM
For the NEC Havana ezs. Does it work

Thanks

Sent from my SM-N960F using Tapatalk

with this NEC havana nothing work, you must install filters

[javyb]

with this NEC havana nothing work, you must install filters

This update is supposed to install a virtual filter so km shows same as dash. Diagprog 4 can do this aswell but just wondered if anybody had experienced with smok

Sent from my SM-N960F using Tapatalk

[cokolo]

Anybody any experience with licence
MS0008 Mercedes W251, W164, X164 EZS KM
For the NEC Havana ezs. Does it work

Thanks

Sent from my SM-N960F using Tapatalk

Work extra change km on OBD in 2 sec these is first generation with NEC Amazon and these NEC is from 2009-11 year . No install can filter or flashing CGW , new km in ezs in 2 sec and 100% work

[esse]

Hi,
i need change mileage in DSG DQ 250 from A3 2016 but i don t know which licence i need to bought
EU 0021 or VW0008
Thanks

[cokolo]

Hi,
i need change mileage in DSG DQ 250 from A3 2016 but i don t know which licence i need to bought
EU 0021 or VW0008
Thanks

Not possible with any license you must put DSG filter to solve that problem