>>>>>>>>SMOK SUPPORT THREAD<<<<<<<

**amigokola** · 16th July, 2018, 10:31 AM

Someone here swapped MM cluster (Mii,Up,Citigo) with success ??
I read ori and new (used) and got all data.
Prepared new eeprom and wrote it with programmer to new dash (SAFE on LCD).
I did Immo4 UDS option in SMOK and all went smooth. Learned key (key accepted so CS,PIN has to be right) but still SAFE on dash.
I think MAC is the problem. Dont know if SMOK works with this MM dash as IMMO4UDS option (it is not listed in manual) ??
Any ideas are welcome...

**ghostrider72** · 16th July, 2018, 10:55 AM

Try VVDI2 mate.
I didn’t replace dash just coded mechanical key with and worked fine.

**amigokola** · 16th July, 2018, 12:35 PM

Yes adding key works with VVDI2 and SMOK but when I write data by OBD2 with VVDI2 SAFE on LCD.

Originally Posted by ghostrider72

Try VVDI2 mate.
I didn’t replace dash just coded mechanical key with and worked fine.

**ghostrider72** · 16th July, 2018, 01:01 PM

Type down all data manually instead of copy it. Than make new transponders

**amigokola** · 16th July, 2018, 07:43 PM

I've already did it and immo see keys as dealer key. I wrote all data by hand and still SAFE on dash. This car is killing me...

Originally Posted by ghostrider72

Type down all data manually instead of copy it. Than make new transponders

**ghostrider72** · 16th July, 2018, 08:00 PM

Pretty sure there is option in SMOK to pair clocks with ecu. I’ve used it only once or twice in the past. Worth to try that as well

**qeso705** · 16th July, 2018, 08:33 PM

Power class match? Did you perform ecu learning to dash?

**amigokola** · 16th July, 2018, 09:48 PM

I did Immo4 UDS and all went smooth. Disconnected battery for 15min but still SAFE on dash. Problem is in ecu-immo line. I think MAC but even when I login it doesnt help. It is ME17.5 so I dont know if Smok works good with this ecu combined with MM dash... What tool decode data feom this ecu ??

Wysłane z mojego SM-G950F przy użyciu Tapatalka

**yugo45** · 19th July, 2018, 10:14 PM

Originally Posted by amigokola

I did Immo4 UDS and all went smooth. Disconnected battery for 15min but still SAFE on dash. Problem is in ecu-immo line. I think MAC but even when I login it doesnt help. It is ME17.5 so I dont know if Smok works good with this ecu combined with MM dash... What tool decode data feom this ecu ??

Wysłane z mojego SM-G950F przy użyciu Tapatalka

Try direct read at ECU with SMOK , it should decode data.

**djollie** · 20th July, 2018, 02:40 AM

can smok do CITROEN C1 2017 MILEAGE ?

i haven't got to the car yet so no idea what bsi or cluster is in it???

**idealb2** · 20th July, 2018, 03:33 AM

Can smok uhds do peuguet 3008 2017 odometer

**teerak2uk** · 20th July, 2018, 07:14 AM

Originally Posted by djollie

can smok do CITROEN C1 2017 MILEAGE ?

i haven't got to the car yet so no idea what bsi or cluster is in it???

Is c1 not a toyota underneath and dash/eeprom only???

**Maartinj** · 20th July, 2018, 08:45 AM

Originally Posted by amigokola

I did Immo4 UDS and all went smooth. Disconnected battery for 15min but still SAFE on dash. Problem is in ecu-immo line. I think MAC but even when I login it doesnt help. It is ME17.5 so I dont know if Smok works good with this ecu combined with MM dash... What tool decode data feom this ecu ??

Wysłane z mojego SM-G950F przy użyciu Tapatalka

simple disconnect ECU to see if cluster see KEY and message gone