Toyota 4 runner 2015 Steering angle
Register
Page 1 of 3 123 LastLast
Results 1 to 15 of 42
  1. #1
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default Toyota 4 runner 2015 Steering angle

    Need to unlock a Steering angle sensor Panasonic 89245-30110 it has 24cs02a it has internal error and is stuck in -834deg, tryed dump from good sensor and now it reads until 45deg and gets error, think need to virginize dump in order to self align magnets inside, I tryed a lot of positions of magnets but hard to set to 0 deg, has anyone method to virgin dump and recover sensor, thanks.

  2. #2
    DK Veteran
    Brayn's Avatar
    Join Date
    Oct 2015
    Location
    Colombo
    Posts
    1,202
    Thanks Thanks Given 
    337
    Thanks Thanks Received 
    1,507
    Thanked in
    522 Posts

    Default

    Quote Originally Posted by luis12 View Post
    Need to unlock a Steering angle sensor Panasonic 89245-30110 it has 24cs02a it has internal error and is stuck in -834deg, tryed dump from good sensor and now it reads until 45deg and gets error, think need to virginize dump in order to self align magnets inside, I tryed a lot of positions of magnets but hard to set to 0 deg, has anyone method to virgin dump and recover sensor, thanks.
    Post your dump file I can check it

    Sent from my C5502 using Tapatalk

  3. The Following User Says Thank You to Brayn For This Useful Post:

    LooserX (9th May, 2017)

  4. #3
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default

    Hello friend, this is orig dump with error...
    Attached Files Attached Files

  5. The Following User Says Thank You to luis12 For This Useful Post:

    br.balazs (25th February, 2017)

  6. #4
    DK Veteran
    Brayn's Avatar
    Join Date
    Oct 2015
    Location
    Colombo
    Posts
    1,202
    Thanks Thanks Given 
    337
    Thanks Thanks Received 
    1,507
    Thanked in
    522 Posts

    Default

    here you go
    try and report please
    DTC should goes off
    after Test mode run for 1 minuets
    Attached Files Attached Files

  7. The Following 7 Users Say Thank You to Brayn For This Useful Post:

    br.balazs (25th February, 2017), Dotcom2509 (5th December, 2018), Javed11 (12th June, 2017), LooserX (9th May, 2017), luis12 (1st November, 2016), pcofre (1st October, 2019), ZIOMAL4340 (4th October, 2017)

  8. #5
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default

    No luck friend, error appears in 20degrees or more, I test with a good sensor dump and same issue, tryed good board on bad sensor body (magnets assembly) Works OK, so magnets dont are problema, think that need a virgin dump to try recover it or perhaps micro has part of culprit, any one has solved this ?? I see Iprog has solution. Thanks any help.

  9. #6
    DK Veteran
    Brayn's Avatar
    Join Date
    Oct 2015
    Location
    Colombo
    Posts
    1,202
    Thanks Thanks Given 
    337
    Thanks Thanks Received 
    1,507
    Thanked in
    522 Posts

    Default

    Quote Originally Posted by luis12 View Post
    No luck friend, error appears in 20degrees or more, I test with a good sensor dump and same issue, tryed good board on bad sensor body (magnets assembly) Works OK, so magnets dont are problema, think that need a virgin dump to try recover it or perhaps micro has part of culprit, any one has solved this ?? I see Iprog has solution. Thanks any help.
    ????
    After write my files what happen??
    Write my files turn on ignition then check what dtc have
    Clear dtc and check all dtc gone if yes
    Go to Abs system and utility Test mode run. Also check how about degree have
    It should be 0 when steering wheel ahead

    Sent from my C5502 using Tapatalk

  10. The Following 5 Users Say Thank You to Brayn For This Useful Post:

    cougar89 (23rd April, 2018), LooserX (9th May, 2017), luis12 (2nd November, 2016), rtbdiagnostic (12th January, 2020), vanos batam (2nd February, 2022)

  11. #7
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default

    Ok the blockage gones, now I center sensor and conect then read is about 0 degrees so when moves to any direction counter or clockwise at about 10 deg it takes error telling internal error and again turn on warn light, tryed with good sensor and put good file to bad sensor and same result, question you can interchange a good dump from good sensor to any bad sensor ? or it has any sincro. Thanks for your help friend.

  12. #8
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default

    SOLVED... thanks to BRAYN for made a reset wich used to find the problem and make scrypt for solution of futures modules.

  13. The Following User Says Thank You to luis12 For This Useful Post:

    rtbdiagnostic (12th January, 2020)

  14. #9
    DK Veteran

    Join Date
    Jun 2010
    Location
    Canada
    Posts
    1,034
    Thanks Thanks Given 
    322
    Thanks Thanks Received 
    620
    Thanked in
    269 Posts

    Default

    Quote Originally Posted by luis12 View Post
    SOLVED... thanks to BRAYN for made a reset wich used to find the problem and make scrypt for solution of futures modules.
    could you share the solution please is the chip in angle sensor,, I am having same issue with 2013 lexus RX350 stuck at 842 degrees

    thanx
    If i helped you please press thanx

  15. The Following User Says Thank You to janushaan For This Useful Post:

    Javed11 (10th May, 2017)

  16. #10
    Banned
    Join Date
    Mar 2017
    Location
    Russia, Ural
    Posts
    9
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    14
    Thanked in
    3 Posts

    Default

    Everyone who is doing this again: 1. don't move the magnets never. 2. Use only the native dump
    I have the solution for 89245-74010, 89245-74020, 89245-30110

  17. #11
    Newbie
    Join Date
    May 2017
    Posts
    1
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default 4runner 2016

    Quote Originally Posted by SoftDump View Post
    Everyone who is doing this again: 1. don't move the magnets never. 2. Use only the native dump
    I have the solution for 89245-74010, 89245-74020, 89245-30110

    hi,

    i have a toyota 4runner 2016 and i have c1433 code, i already scan with easydiag x431 and try to reset but i have the slip light on and the steering symbol light on too, i can repair my sensor? when i scan the angle says -864 deg

    thanks a lot

  18. #12
    DK Veteran
    luis12's Avatar
    Join Date
    Jan 2011
    Location
    Panama
    Posts
    907
    Thanks Thanks Given 
    241
    Thanks Thanks Received 
    133
    Thanked in
    86 Posts

    Default

    Friend this problem sets when you detach Sir coil and turn Wheel more than 2 1/2 turn to any direction, maxium permit is 2 turns from center, if exeeds the known +854 or -854 sets. Only way to recover is cleaning error from eprom

  19. The Following User Says Thank You to luis12 For This Useful Post:

    rtbdiagnostic (14th August, 2019)

  20. #13
    Member chong5195's Avatar
    Join Date
    Nov 2016
    Posts
    88
    Thanks Thanks Given 
    14
    Thanks Thanks Received 
    7
    Thanked in
    6 Posts

    Default i has lexus same problem with this angle.. can share the dump pls ..

    pls share me l the dump for steering angel. 89245-30110 pls help ,, can send my email.. *Removed Email Adress...
    Last edited by Johnner; 10th October, 2017 at 11:17 PM.

  21. #14
    Newbie
    Join Date
    Oct 2017
    Posts
    13
    Thanks Thanks Given 
    5
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Quote Originally Posted by SoftDump View Post
    Everyone who is doing this again: 1. don't move the magnets never. 2. Use only the native dump
    I have the solution for 89245-74010, 89245-74020, 89245-30110
    I have 89245-74010 plz help me to reset

    Sent from my SM-J700F using Tapatalk

  22. #15
    Senior Member

    Join Date
    Dec 2017
    Posts
    258
    Thanks Thanks Given 
    135
    Thanks Thanks Received 
    172
    Thanked in
    36 Posts

    Default help me

    Quote Originally Posted by Brayn View Post
    here you go
    try and report please
    DTC should goes off
    after Test mode run for 1 minuets
    pls pass, thank you

 

 
Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.