Reply With QuoteI have the same problem unfortunately, still looking for a solution...
Results 1 to 15 of 17
Thread: spc560 verify error xprog
-
8th February, 2017, 10:34 AM #1DK Veteran
- Join Date
- Dec 2011
- Location
- t?rkiye yozgat
- Posts
- 740
- Thanks
- 96
- Thanks
- 52
- Thanked in
- 43 Posts
spc560 verify error xprog
spc560 verify error xprog 5.55 read not work help please
-
26th July, 2017, 06:08 PM #2Member
- Join Date
- May 2017
- Location
- City 17
- Posts
- 47
- Thanks
- 25
- Thanks
- 35
- Thanked in
- 10 Posts
-
26th July, 2017, 06:27 PM #3DK Veteran
- Join Date
- Nov 2015
- Location
- Lublin/poland
- Posts
- 621
- Thanks
- 177
- Thanks
- 245
- Thanked in
- 141 Posts
check read cable com (rs232) and plug power 12v xprog
-
The Following User Says Thank You to kostrz3 For This Useful Post:
navatar (28th July, 2017)
-
26th July, 2017, 07:07 PM #4DK Veteran
- Join Date
- May 2010
- Location
- near THE NORTH FACE
- Posts
- 828
- Thanks
- 272
- Thanks
- 55
- Thanked in
- 46 Posts
If you want to read and write spc with a low budget programmer look at the segger jtag on ebay and you will be
happy with that interface ( little bit confusing software interface but nice working ) you kan read and write without
errors and problem that kind of processor , i was in trouble with xprog and at the end downgraded and working good
for now only with older software
REGARDS
-
The Following User Says Thank You to dariobmw For This Useful Post:
navatar (28th July, 2017)
-
28th July, 2017, 05:21 AM #5DK Veteran
- Join Date
- Aug 2014
- Location
- USA, Earth, Milky Way Galaxy, Universe, Unknown
- Posts
- 1,441
- Thanks
- 518
- Thanks
- 1,682
- Thanked in
- 745 Posts
The verify errors in xprog is the software. I've noticed on a fresh install I can open the program and have no trouble programming the first 2 or 3, after that I get Verify errors
-
28th July, 2017, 07:03 AM #6Top Poster
- Join Date
- Oct 2015
- Posts
- 127
- Thanks
- 21
- Thanks
- 6
- Thanked in
- 3 Posts
the solution that worked fine and tested for all my friends
Dacia_v2 spc560p50l3 v2 xprog pinout.jpg
-
The Following 4 Users Say Thank You to alaaengineer For This Useful Post:
beongo (7th July, 2020), mexanico1971 (17th June, 2020), navatar (28th July, 2017), raskolnikov1975 (4th February, 2019)
-
28th July, 2017, 10:04 AM #7DK Veteran
- Join Date
- Oct 2015
- Location
- Poland
- Posts
- 901
- Thanks
- 411
- Thanks
- 263
- Thanked in
- 179 Posts
when use xprog im off internet connection.
-
The Following User Says Thank You to castin For This Useful Post:
navatar (28th July, 2017)
-
28th July, 2017, 01:55 PM #8DK Veteran
- Join Date
- Nov 2015
- Location
- Lublin/poland
- Posts
- 621
- Thanks
- 177
- Thanks
- 245
- Thanked in
- 141 Posts
Originally Posted by navatar
use cable com (rs232) and put power xprog +12v
test and report
-
The Following User Says Thank You to kostrz3 For This Useful Post:
navatar (28th July, 2017)
-
28th July, 2017, 04:32 PM #9Member
- Join Date
- May 2017
- Location
- City 17
- Posts
- 47
- Thanks
- 25
- Thanks
- 35
- Thanked in
- 10 Posts
Hi everyone thanks for solutions resolved it by setting the X-Prog COM port latency in device manager to 1ms instead of 16.
-
The Following User Says Thank You to navatar For This Useful Post:
ivantolobrabus (8th October, 2018)
-
28th July, 2017, 09:02 PM #10Member
- Join Date
- May 2017
- Location
- City 17
- Posts
- 47
- Thanks
- 25
- Thanks
- 35
- Thanked in
- 10 Posts
Spoke too soon still have errors going to try direct rs232 and 12v tomorrow
-
28th July, 2017, 09:16 PM #11Member
- Join Date
- May 2017
- Location
- City 17
- Posts
- 47
- Thanks
- 25
- Thanks
- 35
- Thanked in
- 10 Posts
Hi don't think software is at fault as I did fresh install of Xprog 5.55 on a new computer which was never connected to internet and problems are same
-
The Following User Says Thank You to navatar For This Useful Post:
repairmymodule (29th July, 2017)
-
28th July, 2017, 09:59 PM #12DK Veteran
- Join Date
- Aug 2009
- Location
- Centurion,South Africa
- Posts
- 2,141
- Thanks
- 1,033
- Thanks
- 621
- Thanked in
- 305 Posts
True
Is not actuall programmer crack software problem m8
-
28th July, 2017, 10:16 PM #13DK Veteran
- Join Date
- Aug 2009
- Location
- Centurion,South Africa
- Posts
- 2,141
- Thanks
- 1,033
- Thanks
- 621
- Thanked in
- 305 Posts
As stable with original as War of something i believe ./.........
-
29th July, 2017, 05:04 AM #14DK Veteran
- Join Date
- Aug 2014
- Location
- USA, Earth, Milky Way Galaxy, Universe, Unknown
- Posts
- 1,441
- Thanks
- 518
- Thanks
- 1,682
- Thanked in
- 745 Posts
With me, the software is the case. 100% sure about it. I have clone xprog box 5.55
-
30th July, 2017, 06:30 PM #15Member
- Join Date
- May 2017
- Location
- City 17
- Posts
- 47
- Thanks
- 25
- Thanks
- 35
- Thanked in
- 10 Posts
Hi guys thanks for all the help finally got a solution for SPC560 verify errors used a different software version mutec99 on MHH titled "XProg 5.55 no dongle". Link is attached
-
The Following 4 Users Say Thank You to navatar For This Useful Post:
heatgun (23rd December, 2018), repairmymodule (30th July, 2017), Sarah1331 (3rd February, 2019), YASS59 (25th August, 2020)
Bookmarks