a3 8P can bus wake up
Register
Results 1 to 13 of 13
  1. #1
    DK Veteran

    Join Date
    Aug 2015
    Posts
    704
    Thanks Thanks Given 
    176
    Thanks Thanks Received 
    142
    Thanked in
    120 Posts

    Default a3 8P can bus wake up

    Can someone help me i need canbus wakeup signal to get cluster on bench working

    diagnostic is working but wake up signal is missing

  2. #2
    DK Veteran

    Join Date
    Dec 2009
    Posts
    2,204
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    879
    Thanked in
    532 Posts

    Default

    Wake up is coming via CAN from central electric
    If you have CAN logger you can send the wake up CAN message otherwise get central electric

  3. The Following User Says Thank You to exe123 For This Useful Post:

    offsystem (20th March, 2017)

  4. #3
    DK Veteran

    Join Date
    Aug 2015
    Posts
    704
    Thanks Thanks Given 
    176
    Thanks Thanks Received 
    142
    Thanked in
    120 Posts

    Default

    Do you have the cansignal logged maybe? I have sniffer.

    Must i sniff the message from Kombi can by the Cluster?

  5. #4
    Junior Member
    Join Date
    Dec 2013
    Posts
    38
    Thanks Thanks Given 
    7
    Thanks Thanks Received 
    14
    Thanked in
    12 Posts

    Default

    Send this to the bus : ID:575 DLC:2 DATA: 07 00 every 200ms


  6. The Following User Says Thank You to ungask For This Useful Post:

    offsystem (21st March, 2017)

  7. #5
    DK Veteran
    rob h's Avatar
    Join Date
    May 2011
    Posts
    4,405
    Thanks Thanks Given 
    1,815
    Thanks Thanks Received 
    2,072
    Thanked in
    1,457 Posts

    Default

    pressing the time button might do something

  8. #6
    DK Veteran

    Join Date
    Aug 2015
    Posts
    704
    Thanks Thanks Given 
    176
    Thanks Thanks Received 
    142
    Thanked in
    120 Posts

    Default

    Quote Originally Posted by ungask View Post
    Send this to the bus : ID:575 DLC:2 DATA: 07 00 every 200ms

    Not working

  9. #7
    DK Veteran

    Join Date
    Dec 2009
    Posts
    2,204
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    879
    Thanked in
    532 Posts

    Default

    You need to send this message on KOMBI-CAN. It will not work via diagnostic CAN

  10. The Following User Says Thank You to exe123 For This Useful Post:

    offsystem (21st March, 2017)

  11. #8
    DK Veteran

    Join Date
    Aug 2015
    Posts
    704
    Thanks Thanks Given 
    176
    Thanks Thanks Received 
    142
    Thanked in
    120 Posts

    Default

    Yes is working now thx

  12. #9
    Top Poster
    Join Date
    May 2013
    Location
    United Kingdom
    Posts
    142
    Thanks Thanks Given 
    7
    Thanks Thanks Received 
    46
    Thanked in
    20 Posts

    Default

    need help with can messages to power on TT 8S virtual cockpit cluster

    i have VECTOR can lin interface to send can messages

    will pay for all infos if is necesar

  13. #10
    Member

    Join Date
    Feb 2018
    Posts
    75
    Thanks Thanks Given 
    4
    Thanks Thanks Received 
    31
    Thanked in
    27 Posts

    Default

    I send ID:575 DLC:2 DATA: 07 00 every 200ms to can (pin29/pin30), but dash did not power up. With pressing the time buttons itīs possible to connect to vcds or other tool, so the wiring in general is correct. Only something with the can message for ignition is wrong.

    Is sending can message to pins 29/30 (can high/low) correct?
    Last edited by akidor; 5th September, 2020 at 11:34 PM.

  14. #11
    Top Poster
    Join Date
    May 2013
    Location
    United Kingdom
    Posts
    142
    Thanks Thanks Given 
    7
    Thanks Thanks Received 
    46
    Thanked in
    20 Posts

    Default

    Id 3c0 message 00000300




    Append 00 00 00 00 in case you need 8 bytes


    your ideea is correct only for OLD clusters ID:575 DLC:2 DATA: 07 00 every 200ms

  15. #12
    Member

    Join Date
    Feb 2018
    Posts
    75
    Thanks Thanks Given 
    4
    Thanks Thanks Received 
    31
    Thanked in
    27 Posts

    Default

    Got it, it was a bad mistake.

    Send ID:575 DLC:4 DATA: 07 00 to cluster via can and it worked.

  16. #13
    Top Poster tec.guilherme's Avatar
    Join Date
    Jun 2010
    Location
    Brasil
    Posts
    132
    Thanks Thanks Given 
    9
    Thanks Thanks Received 
    7
    Thanked in
    6 Posts

    Default

    Hi guys I pay for information and code in ARDUINO, I need wake up this cluster in bench, if possible help me here.

    The corrects is what?

    Because I order parts I plug all BCM 3 Conector Bordnetz Instrument Cluster and Gateway, only when input Line 15 display at clock and mileage still on for some time and later need off and on our press bottons for show.

    I need wakeup cluster for see display.

    The correct Frame is:

    ID:575 DLC:2 DATA: 07 00 every 200ms

    ID:575 DLC:4 DATA: 07 00

    Mr Krakers told: Append 00 00 00 00 in case you need 8 bytes

    Please any one can help.

    Regards

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.