hi buddy
where are you from?
i do these very not very dificult.
send me your 24c02 file
Hi,
How can i reprogram Eprom 24C02 with software?
I've made dump with Immokiller, but when i want to write immo-off file in engine, it doesn't work.
I have errors message.
I have VW Golf 3 with Bosch Motronic MP9, 24C02 Eeprom and 87C510 Eprom.
I don't find that Ecu in Immokiller.
So, which software can i use to write immo-off file in Eprom?
Immo Tool, etc?
Thank you
hi buddy
where are you from?
i do these very not very dificult.
send me your 24c02 file
bh01 (21st July, 2017)
The answer is over here http://www.digital-kaos.co.uk/forums...=1#post3075918
Love this forum
bh01 (21st July, 2017)
Thank you.
I have already immo-off file.
But, i can't write it to Ecu.
I used Immo killer but not work with my Ecu.
I don't know about all software.
I want to know just two things.
Which software can i use as i'll be sure it'll work for my Ecu?
Do i have to unplug the immobox to make it work, and how to unplug?
hi buddy
you need to have serial eeprom programmer
uupa, tl866, orange, ect
remove the chip from the board, use programmer to write the chip, refit chip to the board
Thank you.
I don't have programmer.
I can't write with sofware?
So the file that is now Immo Off is NOT from your ecu ?
Read Saintgp Post Ok
I made dump file with Immokiller.
Then, i asked here someone to make me immo-off file and i thank him.
But now, i wanted to write it to Ecu with immokiller too, but not work.
There's not my Ecu in Immokiller listing.
So, i have errors message.
Lets Try again, how / where did you get the file that you used Immokiler to demobilize ?
Thnak you.
Well, i used Immokiller to make dump of Eprom.
Then, i made a post in that forum to ask somebody for immo-off with my dump file.
A member made it and post it in reply.
After that, i tried to write that immo-off file with Immokiller. But, there's not my Ecu in VW part.
So, the operation return an errors message.
I turned on the car like usual, and worked.
But, as usual, the car turned off after 1 second, cause of Immobilizer.
So, i wonder if i did all well, and if i have to unplug Immobilizer and its antenna from Ecu and ignition.
Ok. what are you using to read Eeprom ?
Post your 2 files here so we can see where is your problem Ok
If There is immo box YES Disconnect it
bh01 (22nd July, 2017)
on the vw mp9 system theres no need to unplug immo box. i have done many of these and never once unpluged a immo
bh01 (22nd July, 2017)
Hi, you must open ecu and look for small bug with eight leg 24c02, desolder from board, read from chip, post data here and someone change data in file for you. You write data in small bug and solder back in ecu. Then put in car and try start. If ewerithink is ok car work with no immo. Understand?
Welkome in DK
You need a programer or someone who have it and good solderstation too
Last edited by Pyromaniak; 22nd July, 2017 at 12:48 PM.
My English is little bit bad, but day after day is better. Like my experiences https://www.youtube.com/channel/UCdT...bx2Pc7WI4pWUWA
My help not for free, press THANKS and REP, for make me HAPPY
im not using passwords, my work is for this forum and members free
bh01 (22nd July, 2017)
Hi, everybody!
Thank you all for your help.
I use a Vag-com cable with Vcds software to communicate with Ecu, and Eeprom.
I can so read the chip and dump the file.
But, then, i can't write it to Eeprom cause i don't find my Ecu in the software i used to dump Eeprom file (Immokiller).
I join the two files : original and immo-off file
P.S. : I will try again with another software and will retrun here.
Hi, the original file it's empty. It's not good read.
You must read with programer. If you don't have search in google ponyprog.
bh01 (22nd July, 2017)
Bookmarks