Outlander 2013 93c76 Micro V2
Register
Page 1 of 2 12 LastLast
Results 1 to 15 of 24
  1. #1
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default Outlander 2013 93c76 Micro V2

    Hello.
    digiprog is not reading . I think I connect right 6 wires but its showes chip not found.

  2. #2
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

  3. #3
    DK Veteran

    Join Date
    Jan 2017
    Location
    IN CIRCUIT
    Posts
    357
    Thanks Thanks Given 
    155
    Thanks Thanks Received 
    70
    Thanked in
    57 Posts

    Default

    YOUR COLORS ARE THE CORRECT OR IS CHINESE CLON ???

  4. #4
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    Yes. colors same as original. Now i got reading eeprom only 0 showes nothing else. Is that normal? dash is home without power on. did i somthing wrong? i was only reading not writing.

    Aslo i just came back from the car, all looks like was before but when then im connecting DigiProg all dash get OFF. Do i do somthing wrong? Or when ST47 is connected to the chip i shouldn't connecting power and digiprog same time?
    Last edited by defected; 11th August, 2017 at 08:28 PM.

  5. #5
    V.I.P. Member

    Join Date
    Sep 2009
    Posts
    6,970
    Thanks Thanks Given 
    2,250
    Thanks Thanks Received 
    7,802
    Thanked in
    4,913 Posts

    Default

    unsolder eeprom.......................

  6. #6
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    Is that only way to do anything with eeprom? Its micro have no place on Digiprog to solder there.
    Still nothing ;( there is instruction on Enigma how to do so it should be just fine, same connection and is not working.
    Chip is micro V2 dont know to do.
    Last edited by defected; 12th August, 2017 at 10:08 AM.

  7. #7
    DK Veteran
    Cardiag.ru's Avatar
    Join Date
    Apr 2010
    Location
    Russia
    Posts
    443
    Thanks Thanks Given 
    15
    Thanks Thanks Received 
    433
    Thanked in
    199 Posts

    Default

    Present better way to make this dashboard
    https://www.youtube.com/watch?v=23YWFTbgTp4

  8. #8
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    After removing 1 wire form dash i got reading. eeprom and km. two times the km was correct and later stars showing more km and after 0 again but eeprom can read.
    here is dump of my eeprom, can you check if is correct? also should i risk and change km even when digiprog is showing old km 0 but reading eeprom?
    Attached Files Attached Files

  9. #9
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    And how much that soft can cost?
    Can you look on my eeprom?

  10. #10
    V.I.P. Member

    Join Date
    Sep 2009
    Posts
    6,970
    Thanks Thanks Given 
    2,250
    Thanks Thanks Received 
    7,802
    Thanked in
    4,913 Posts

    Default

    this 93c76
    read as 93c76

  11. #11
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    when i read 93C76 or 93C86 numbers in eeprom same numbers.
    can save 93C76 but from digiprog to pc can not is some error.
    93c76 Type ?:29 and cant save to pc (type error in eetool for digiprog)
    93C86 type 93C86 and can save (type no error in eetool for digiprog)
    but in Digiprog looks good no error. Can you check that 93C86 if is good?

  12. #12
    DK Veteran

    Join Date
    May 2010
    Posts
    4,319
    Thanks Thanks Given 
    533
    Thanks Thanks Received 
    1,132
    Thanked in
    902 Posts

    Default

    original mileage 68384km

  13. #13
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    yes its 68... somthing. Now is not reading again. no eeprom no nothing. km 0 , eeprom 0
    any ideas why is so unstable? this chip is V2 micro.
    connected like on picture but with ST47 digiprog wirea.jpgb.jpgc.jpg

  14. #14
    Top Poster
    Join Date
    Oct 2015
    Location
    Tokyo
    Posts
    123
    Thanks Thanks Given 
    17
    Thanks Thanks Received 
    4
    Thanked in
    3 Posts

    Default

    upss.
    connecting to the car dash not working:/ lcd not powered. is chip gone or i did something more . was nothing changing in eepron.

  15. #15
    V.I.P. Member
    Cllau's Avatar
    Join Date
    Mar 2017
    Location
    where friends need me
    Posts
    2,573
    Thanks Thanks Given 
    292
    Thanks Thanks Received 
    5,380
    Thanked in
    1,641 Posts

    Default

    unsolder eeprom and read as 93c76...

 

 
Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.