ISN: 3A3F0E196F088916BB1EDFBBE14DA9D5
Hi, long story short: original ECU eeprom corrupt, i have only full backup with KESS. I wrote to original ECU exact the same software(donor) but ISN in eeprom is different. After that i overwrote full_backup_kess, but ISN didnt change. I have CAS eeprom, ECU eeprom(new), original ISN code from CAS and key info - all in attachment. Can somobody write that ISN to ECU eeprom? If i do it manually, it doesnt work - i think you need checksum around 3 lines of ISN... I did also immo off in flash, but there are still fault codes and red light in dash. Please help.
Thank you
Al
ISN: 3A3F0E196F088916BB1EDFBBE14DA9D5
Zaklberg (24th September, 2017)
Thanks for reply, can i overwrite this ISN in ECU eeprom? What about checksum?
Al
Yes you can write ISN to ECU
or
synch DME and CAS with VVDI 2
best regards
Ok, i wrote ISN to ECU eeprom, but still gives me error 2E3B EWS manipulation. I also tried cas dde synchronisation with vvdi2, but it is not possible. Any other solution - maybe can you write ISN from ecu to CAS?
Thanks
Al
...............
Last edited by kiszka; 21st December, 2018 at 11:19 PM.
Reality of life :
1:Never argue with an idiot, he will pull you down to his level and overcome you with experience
2:Envy is the confession of inferiority
3:Everyone lies
---------------------------------------------------------------
How much trash you leave behind so much trash someone will have to read or maybe you yourself
If you like reading garbage, don't slow down, just speed it up
Ok, original CAS eeprom and ECU eeprom with donor ISK.
Thanks
Al
...............
Last edited by kiszka; 21st December, 2018 at 11:19 PM.
Reality of life :
1:Never argue with an idiot, he will pull you down to his level and overcome you with experience
2:Envy is the confession of inferiority
3:Everyone lies
---------------------------------------------------------------
How much trash you leave behind so much trash someone will have to read or maybe you yourself
If you like reading garbage, don't slow down, just speed it up
Zaklberg (24th September, 2017)
Thank you for helping, sir, but the folder is empty i think
Al
FVDI can do
Snycro ---> CAS and ECU
no need syncro on long isn and cannot duet
Professional bmw key service cas 3/3+ 4/4+ repair = reset ews egs 8hp = 6hp-egs19d
Zaklberg (24th September, 2017)
I also think all i need is that ISN from my first post to be written in ECU eeprom. That should work - i copy ECU eeprom from another car into my ECU and put it into that car and it started - no ews manipulation(with a bunch of error codes...). I think problem is in eeprom checksum - ISN is repeated 3 times and aroud it are different bytes(i guess checksum).
Al
...............
Last edited by kiszka; 21st December, 2018 at 11:20 PM.
Reality of life :
1:Never argue with an idiot, he will pull you down to his level and overcome you with experience
2:Envy is the confession of inferiority
3:Everyone lies
---------------------------------------------------------------
How much trash you leave behind so much trash someone will have to read or maybe you yourself
If you like reading garbage, don't slow down, just speed it up
Zaklberg (24th September, 2017)
You have 2 option...
1-You change ISN in ECU dump and post here Ori dump and dump after written ISN...
2-You change ISN in Cas but you need to read "real page3" in your working key...
Bookmarks