Nissan QASHQAI J10 key
Register
Results 1 to 9 of 9
  1. #1
    DK Veteran
    daniersms's Avatar
    Join Date
    Feb 2010
    Location
    South Africa
    Posts
    1,355
    Thanks Thanks Given 
    755
    Thanks Thanks Received 
    510
    Thanked in
    282 Posts

    Default Nissan QASHQAI J10 key

    Can anybody please help with the configuration data on a 2010 Qashqai J10 remote key please
    Love this forum

  2. #2
    DK Veteran
    autochei's Avatar
    Join Date
    Mar 2013
    Location
    romania
    Posts
    1,493
    Thanks Thanks Given 
    426
    Thanks Thanks Received 
    804
    Thanked in
    587 Posts

    Default

    1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
    2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
    3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
    4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
    5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.


    IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.


    6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
    7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.


    YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.


    Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

  3. The Following 2 Users Say Thank You to autochei For This Useful Post:

    daniersms (26th May, 2018), the_riddler (12th October, 2019)

  4. #3
    DK Veteran
    daniersms's Avatar
    Join Date
    Feb 2010
    Location
    South Africa
    Posts
    1,355
    Thanks Thanks Given 
    755
    Thanks Thanks Received 
    510
    Thanked in
    282 Posts

    Default Nissan QASHQAI J10 key

    Ok this is for the remote programming what I am looking for is the data on the pages .. see photo which is what I have but it is not working
    Attached Images Attached Images
    Love this forum

  5. #4
    DK Veteran
    HeXeN's Avatar
    Join Date
    Mar 2015
    Posts
    1,028
    Thanks Thanks Given 
    992
    Thanks Thanks Received 
    212
    Thanked in
    136 Posts

    Default

    This is new aftermarket key or original used?
    Sorry I thought it was keyless type
    Last edited by HeXeN; 27th May, 2018 at 11:55 PM.

  6. #5
    DK Veteran
    daniersms's Avatar
    Join Date
    Feb 2010
    Location
    South Africa
    Posts
    1,355
    Thanks Thanks Given 
    755
    Thanks Thanks Received 
    510
    Thanked in
    282 Posts

    Default

    This is a new aftermarket
    Love this forum

  7. #6
    DK Veteran
    lion0304's Avatar
    Join Date
    Oct 2014
    Posts
    3,679
    Thanks Thanks Given 
    1,749
    Thanks Thanks Received 
    3,314
    Thanked in
    1,938 Posts

    Default

    Quote Originally Posted by daniersms View Post
    Ok this is for the remote programming what I am looking for is the data on the pages .. see photo which is what I have but it is not working
    Config RCF seem as PCF7946 for Micra K12, D40, Pathfinder .

    I not have yet experience with Qashqai, but it same key as models above 7946 2 buttons.

    Remote and transponder program at the same time. So just program it and report back.
    Be polite. No Thanks + Rep, no HELP!!! Slava Ukcraine. Dead Putler civilians's killers!!!

  8. The Following User Says Thank You to lion0304 For This Useful Post:

    daniersms (27th May, 2018)

  9. #7
    DK Veteran
    HeXeN's Avatar
    Join Date
    Mar 2015
    Posts
    1,028
    Thanks Thanks Given 
    992
    Thanks Thanks Received 
    212
    Thanked in
    136 Posts

    Default

    He wrote is not working.
    If you have effi+zedbul try to precode with effi, it should work.

  10. #8
    Senior Member

    Join Date
    Apr 2013
    Location
    United Kingdom
    Posts
    257
    Thanks Thanks Given 
    167
    Thanks Thanks Received 
    76
    Thanked in
    37 Posts

    Default

    I tried to sniff data out with id46 cloner but wont give me the config data

    Sent from my SM-G930F using Tapatalk
    Hit like and thanks if I've helped you!!

  11. #9
    V.I.P. Member
    smokey08's Avatar
    Join Date
    Mar 2010
    Location
    Essex, UK
    Posts
    2,263
    Thanks Thanks Given 
    577
    Thanks Thanks Received 
    720
    Thanked in
    382 Posts

    Default

    Are you sure you are using the correct pincode? Try both old and new

    Sent from my Pixel 3 using Tapatalk

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.