help coding engine abs passat 2015

**refack** · 17th June, 2018, 03:57 PM

help coding engine abs passat 2015

Sunday,17,June,2018,08:53:35:39744
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x64
VCDS Version: 17.1.3.0 (x64)
Data version: 20170220 DS267.3
www.Ross-Tech.com

VIN: 1VWAR7A35FC050604 License Plate:
Mileage: 23410km-14546mi Repair Order:

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------

Chassis Type: A3 (7N0)
Scan: 01 02 03 05 08 09 10 15 16 17 19 25 2B 36 42 44 46 4F 52 5F
62 72

VIN: 1VWAR7A35FC050604 Mileage: 23410km-14546miles

01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
04-Steering Angle -- Status: OK 0000
05-Acc/Start Auth. -- Status: Malfunction 0010
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
2B-Steer. Col. Lock -- Status: OK 0000
36-Seat Mem. Drvr -- Status: Malfunction 0010
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
4F-Centr. Electr. II -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
5F-Information Electr. -- Status: OK 0000
62-Door, Rear Left -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine (0-32-CDVB) Labels: 03H-907-309-V1.clb
Part No SW: 03H 906 023 CJ HW: 03H 907 309 A
Component: VR6 3.6l FSI H05 2136
Revision: MFH05--- Serial number:
Coding: 00000000000000000000
Shop #: WSC 09003 957 00200
ASAM Dataset: EV_ECM3F6SI01103H906023CJ 001002
ROD: N/A
VCID: 6CD01FF28710B72125-8038

No ASAM data for: "EV_ECM3F6SI01103H906023CJ" (VW41)
1 Fault Found:
2761 - ROD - Unknown Error Code
- 00 [039]
Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 23417 km
Date: 2018.06.17
Time: 21:06:40

Readiness: 1110 0101

-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 02E-927-770.clb
Part No SW: 02E 300 062 K HW: 02E 927 770 AL
Component: GSG DSG AG6 531 4003
Revision: 06253104 Serial number: 00001506270574
Coding: 0000020
Shop #: WSC 09003 957 00200
VCID: 1D360236C42A8EA9E2-8048

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels: 1K0-907-379-60EC1F.clb
Part No SW: 1K0 907 379 CB HW: 1K0 907 379 CB
Component: ESP MK60EC1 H46 0174
Revision: 00H46001
Coding: 0000000000000000000000000000000000000000
Shop #: WSC 09003 957 00200
VCID: 74E00792D7206FE1FD-8020

1 Fault Found:
01042 - Control Module; Not Coded
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 2
Fault Frequency: 1
Reset counter: 65
Time Indication: 0
Date: 2018.06.17
Time: 21:06:41

Freeze Frame:
Count: 2
Count: 12
Count: 20992
Count: 195
Count: 39680
Count: 0
Count: 0
Count: 0

**autodiagnostix** · 17th June, 2018, 10:09 PM

Chassis Type: A3 (7N0) ???? PASSAT ????
anyhow,
please give us some history of how and when this problem occured , if the car is still under warranty , if the car still starts (i doubt it though) and a brief description of how experienced you are with coding a car / if u do this professionally etc
also please post a complete scan - you can reduce the ammount of rod errors on vcds by updating vcds OR if u close vcds switch the ignition off disconnect the usb cable ignition on cable on vcds on and scan do not perform test since youve done that already
this would give everyone a better picture of whats going on and increase your chances of getting help here quicker

**binhr21** · 21st February, 2020, 01:24 PM

Originally Posted by autodiagnostix

Chassis Type: A3 (7N0) ???? PASSAT ????
anyhow,
please give us some history of how and when this problem occured , if the car is still under warranty , if the car still starts (i doubt it though) and a brief description of how experienced you are with coding a car / if u do this professionally etc
also please post a complete scan - you can reduce the ammount of rod errors on vcds by updating vcds OR if u close vcds switch the ignition off disconnect the usb cable ignition on cable on vcds on and scan do not perform test since youve done that already
this would give everyone a better picture of whats going on and increase your chances of getting help here quicker

First of all Thank you for your replay

. The second thing are is the vehicle is warranty no more so the story its all happen suddenly with in the last month after I started my car in the morning a warning came in dashboard showing that ABS the issue so I used my OBDII device and it show that no abs installed in my vehicle so I swapped the old one (1K0 907 379 BK) with a scound hand (1K0 907 379 BL) (the best of my budget can do for me

) after that it showed me that it required a coding for it so I start digging for this matter:
- I tried to figure it out by my self................fail
- I tried some friends (owners of work shop) one them had (Ross-Tech) original one he took all the data he need and posted it in the ross-tech forum the only answer he got take it to work shop LoL no comments..............fail
- now I'm looking for on others forum hopping for some body can help me with it.
so please any one can help me with this issue & thank you all.

....... end of my story......

**binhr21** · 21st February, 2020, 01:32 PM

sorry my bad I didn't notice its was not for me please accept my apology.

**danielslimovschi** · 21st February, 2020, 01:42 PM

When you swap the ABS you lost your coding.
If you have an automatic scan for your car before you swap the ABS, you might be lucky and you will find the coding in saved files.
If NO, you will need only online coding...

**binhr21** · 21st February, 2020, 01:53 PM

Originally Posted by danielslimovschi

When you swap the ABS you lost your coding.
If you have an automatic scan for your car before you swap the ABS, you might be lucky and you will find the coding in saved files.
If NO, you will need only online coding...

the old one it's was reading nothing at all its was showing no abs module in the vehicle, so how I can do the online coding?