lancer evo 7

[digidashaustralia]

hi I have never lost a file but im blaming my adapter I have lost the file for this car its a a 93c56 chip set if ne one has a dump I would really help on this problem it a Mitsubishi lancer evo7 itis a 93c56 chipset ne where near 43000k thank u in advance

[jjservice]

Do you have some more specific info or photo as a reference????
Maybe i can help you...

Sent from my SM-J710GN using Tapatalk

[digidashaustralia]

all I have is Mitsubishi lancer evo 7 with 93c56 chipset

[Mike1001]

JDM Evo 7 dump

https://www.dropbox.com/s/4rwecqekfm...ordan.bin?dl=0

[digidashaustralia]

hi mike thanks for the help but I cannot get it from the drop box is there ne other way to send or maybe post on here again thank u for your help

[clusters]

You could have if you waited a bit, I did.

[Floppyz]

Hallo,
I'm intreted on this thread too...
I've got a evo 9 dashboard in Km (imperial) with eeprom 96c56 corrupted: while reading with Ponyprog 2000 got sone bits faild... rewrite with the same errors and now the odo display doesn't shows nothing at all.
May be a checksum error that lock the dashboard startup?

please help me...

[Mike1001]

Hallo,
I'm intreted on this thread too...
I've got a evo 9 dashboard in Km (imperial) with eeprom 96c56 corrupted: while reading with Ponyprog 2000 got sone bits faild... rewrite with the same errors and now the odo display doesn't shows nothing at all.
May be a checksum error that lock the dashboard startup?

please help me...

No checksum - just bad dump. Have you tried the Evo 7 one above? Should work otherwise I have a 9 one at work.

[Floppyz]

Hi Mike, yes I tried the evo 7 above but nothing, still blank odo display.
My dashborad is EDM obviusly, maybe the evo 7 JDM dump is in miles?
tks

[Floppyz]

Sorry errata corrige:
my eeprpm is a 93c56! not a 96c56 (that naither exist...)

[Mike1001]

Ok - will post an Evo 9 dump tomorrow for you. JDM in kms.

[Diagcar1]

Hi Mike, yes I tried the evo 7 above but nothing, still blank odo display.
My dashborad is EDM obviusly, maybe the evo 7 JDM dump is in miles?
tks

Try to flip bytes.

[Floppyz]

Try to flip bytes.

Swap byte do you mean? I'll try today.

Does anyone have test ponyprog 2000? useing serial-usb converter and direct probe for microwire 16 byte config.F3MZKDIIRXSZ4JF.LARGE.jpg
Pin 6 and 7 connected to +5V

[Floppyz]

Try to flip bytes.

OK GOT IT!!

now I can see right mileage useing same evo 7 file posted above!

Thant to all of you!

[Floppyz]

Sorry I bother you agian, but now i have new problem:
now I have flash the eeprom with the evo 7 dump posted above

- Speedometer lost linearity: before reflash eeprom it indicate 145km/h @ 100Hz signal on pin 12.
now if I realing the needle to 145kmh at 100hz and move frequncy to 50Hz it indicate 40 kmh (not half 145 -> 77 as I supposed...)
here what I read now:

Hz --- km/h
45 --- 20
55 --- 40
71.5 --- 80
91 --- 120
110 --- 160


How can I calibrate it?

Also fuel level do something odd.....