P0610 Error on MAZDA 3

[FFCCSa1F]

I don't know if there's any smarter way of doing this, but I took a look at some of the fixed 93C56 files posted here in a hex editor. A lot of the data is identical or empty in all of them, and I could use that insight to fix one myself. I put together this gif to make it easier to see which data is identical in all of the dumps. If your dump has different data in those areas, there's a good chance that you can just change it to be identical with the other dumps and it'll work fine. I don't know what any of the variable data is, but I have a sneaking suspicion that corruption there isn't as critical.

It should also be noted that the two 220 µF/10 V capacitors in this ECU go bad and should be replaced when doing this repair. I suspect that they might be a part of what causes this problem.

I used an 809H universal programmer to read and write the chip, though I had to desolder it for that to work.

I hope this can be of help to someone!

EDIT: The forum engine automatically turns gifs into jpgs (why?!), so I had to put it in a .zip.

Attachment 967904

[mk5gt]

Mazda 3
P0610 fault with not working cluster
Checked the 93c56 eeprom and according to this thread everything seems to be ok.
Can someone check the file for correctness?
Thanks!

[atom94]

Hello, can somebody help with this file ?
Mazda 3, speedometer not working and dtc p0610.
Can you correct file from 93c56 ?
Many thanks

[mk5gt]

Just an update.
Replaced 93c56 chip.
Wrote the ori file and the p610 fault disappeared.
Tachometer works .

[einet]

Hello

how can also help me to find the solution on this car ?
I have tested many files and not work.

thanks

[gwiazdamb]

Hello

how can also help me to find the solution on this car ?
I have tested many files and not work.

thanks

Replace the memory with a new one

[einet]

Hello

Have chenged with a ST93c56 and error sill there.

[einet]

hello, any can arange me only a Working Dump that not have error ?

thanks

[turboo]

hello pleas help i have p0610 and speedo no work .Thanks

[gwiazdamb]

hello pleas help i have p0610 and speedo no work .Thanks

Please....................

[bladeus86]

Hi, please help i have p0610 and speedo not work, MAzda 3 2004 1.6 petrol
Thanks

[boniing]

Hello everyone, I'm pretty new to this thread and if anyone can give me some advice... On my own car, Mazda 3 BK 2004, 1.6 Tdi, I have a problem and I don't know how to solve it.
When starting the vehicle, the vehicle could not start the electric starter. Ok, I thought the problem was classic. I have checked all the fuses, relays, removed the starter motor and sent it to the shop for repairs etc... And all of that is fixed but the car still won't start the starter motor.
I realized that I have written DTC errors in the car and that's where the problems are.
The errors are:
PATS=B2139 (PATS (Passive Anti Theft System)
data mismatch)
Immobilizer module-PCM=P1260 (Theft Detected, Vehicle Immobilized)
I have saved data from the engine computer because two years ago I did EGR-OFF and I tried to enter that program again in the car, but I didn't succeed.
Does anyone have any advice on how I can solve this?

I have MPPS V18. Is that helpful?

[morgano]

Hi, please help i have p0610 and speedo not work, MAzda 3 2004 1.6 petrol
Thanks

duplicated content, bad read, read it in 16 bit mode.

[sancaman]

Hi.
I also have such a problem. Mazda 1.6 petrol with error code p0610.
Thanks

[gwiazdamb]

Hi.
I also have such a problem. Mazda 1.6 petrol with error code p0610.
Thanks

Please...................


The following errors occurred with your submission

• sancaman has exceeded their stored private messages quota and cannot accept further messages until they clear some space.