NEED PIC DUMP FOR BEEPROG PROGRAMER

**Arbalet73** · 4th November, 2017, 07:58 PM

Please, help me whith file for Beeprog 2.67 clone ,what was check.Thanks.

**Arbalet73** · 4th November, 2017, 07:59 PM

Originally Posted by gopelhu

Hi all,

Here is again the Beeprog PIC content with CFG... ENJOY !!!

Regards, G

This file for Beeprog+

**ykizak** · 5th February, 2019, 02:36 PM

i have a pickit 3.5 clone and i cannot write 40kb files. Size must be 46kb for some reason. Can anyone tell me if there is a way to write 40kb files with mplab x ipe please?

**sabri farid** · 21st April, 2019, 01:19 PM

merci de me aider je cherche les fichier pour beeprog china version 2.67

**hrmotorsport** · 21st April, 2019, 04:13 PM

English please

**tmaa36** · 29th September, 2019, 11:57 AM

thanks thanks thanks

**Rafikvw** · 15th November, 2019, 02:56 PM

Gentlemen, has anyone managed to update Beeprog rice to the latest version? I use 2.92

**RadovanPetkovic** · 18th November, 2019, 10:31 AM

Is it possible that the Beeprog Elnec team stopped my developer work? So far it has worked fine, I bought it as a legal programmer not a Chinese clone. I sent you a report file. If I have to repaire it, write the bin file in PIC and 3xEEproom 24C02? I also send you the read eprom. Does my serial number remain? Help me get my programmer back .... Thanks
When the programmer turns on the voltage. The LEDs are lit at full intensity one at a time by POWER-BUSY-GOOD-ERROR and then remain illuminated by lower-intensity POWER LEDs

**RadovanPetkovic** · 18th November, 2019, 10:42 AM

I'm not sure if the problem is hardware even though I looked through everything without the schema I have good voltages 14V 12v 5v 3.3v 2.7v ..... Or the problem is Software

**RadovanPetkovic** · 21st November, 2019, 11:27 PM

When a man does stupid things. Problem solved. The problem was the version of the program. I knew that my BeeProg was not supported by new versions. But I don't even know how I installed it on the computer I was constantly working on. I installed the other two and I don't remember when I'm on a work computer. Basically the largest version of the software is 3.32 which supports BeeProg. BeeProg2 and BeeProg + can also have New versions. Stupid on my part but when it stops working the most important tool in the workshop ...... PANIC
There is also one good thing about all this, I will share the picture with the required voltages on the board. When someone has a problem with BeeProg hardware ..... Hope no one will have such a problem

BeeProgSupplay1.jpg Supported.jpg

**zapdus** · 4th January, 2020, 03:01 AM

Originally Posted by gopelhu

Hi all,

Here is again the Beeprog PIC content with CFG... ENJOY !!!

Regards, G

I can confirm
It is working
Program with pickit3

**tmaa36** · 19th March, 2020, 06:13 PM

Thanks Elvis

**elgadus** · 13th April, 2020, 07:15 PM

does anybody know if software version 3.0 work with all beeprog clone or only with from there?

**elgadus** · 17th October, 2020, 01:21 PM

RadovanPetkovic.You were able to pick up the Beeprog programmer?

**RadovanPetkovic** · 24th October, 2020, 09:35 PM

BeeProg works great. Be sure to clean the Eprom and processor pins well because BeeProg "sees" the lowest resistance outside of the one listed in the catalog for a given chip. It often reports contact errors for some pins. They will read it only if everything is according to the regulations and that is why they give it that less than 1% is a possible mistake

Thread: NEED PIC DUMP FOR BEEPROG PROGRAMER

Thread Tools

Display

Bookmarks

Bookmarks

Posting Permissions