RENAULT CAN CLIP REPAIR SOLUTION

**pulsar2000** · 5th November, 2014, 11:04 PM

Originally Posted by pulsar2000

Anyone able to repair my clip if i send to them , ? no comms from usb, no leds, dead unit, worked fine then no usb comms, its a china clone, cheaper to send E.u repair, anyone ? willing to pay,,,,

anyone ? if no sending back, willing to pay for a fix,,,

**maaxxyy** · 12th January, 2015, 01:07 AM

Hi guys i have an issue with my clip. Booster pack on car fried my clip so i replaced the 2 quartz and 2 AN2135 on both boards. Now i have firmware update (renamed files in directory) and all leds light up on clip. I can read the vin number from a 2013 traffic but cant detect any ecu on network test. Any help would be great. Thanks

**morfej** · 12th January, 2015, 08:19 AM

Check CAN SJA1000 chip and relay next to it.

**abdelamjid** · 21st October, 2015, 02:09 PM

thinks to all

not work with my clip

update err

plz help me

best regards

**msarae** · 21st December, 2015, 12:35 AM

I have renault can clip V153
and when i using it to make a test for my car it's suddenly disconnected
and then it's begin to work again then disconnect and so on.
so what can I do. in this case

**Med01** · 26th December, 2015, 09:03 PM

Hello Pro Friends
I would like to buy a clone Clip
Any one advice me which one i should buy
I heared that there is Clips with RLT 2002 and others with alliance drivers Boch
Please need advices and how i can know the right one

Envoy? de mon SM-N9005 en utilisant Tapatalk

**Med01** · 26th December, 2015, 09:15 PM

Hello friends

Envoy? de mon SM-N9005 en utilisant Tapatalk

**Med01** · 27th December, 2015, 01:34 AM

Originally Posted by vicman32

hello,
I'm a new clip alliance VI clone.
Green LED flashes and the pc ISO does not recognize the clip.
anyone know it can be. I not find de oscillator.
thanks,
regards.

Hi friend
I want to know how i can know the Clip alliance from other Clips
Is it more beter than other Clips

Thanks

Envoy? de mon SM-N9005 en utilisant Tapatalk

**abdelamjid** · 27th December, 2015, 02:23 PM

thanks to all for sharing

my clip not work plz help me

best regards

**clipcan** · 27th December, 2015, 08:13 PM

Hello,
I have a Clone Clip too.
My Problem is , a newer Megane III with Multiplex Can works fine.
But older Twingo dont.
And when i take not Renault --> Scantool ISO 9141-2 and ISO 14230-4 it didnt work.
In my Computer there is only one Bosch Automotive Service Solution Device --> 1B-Alliance Vehicule Communication Interface

**sepistar** · 14th January, 2016, 10:31 AM

Originally Posted by peko

hi friends
thanks for your help, but nothing change, strange is : with cars all ok, but lot of anothers lose communication always

other solution ?

exactly the same behavior have mine too.
do you find the cure for that?
br.

**dazmoose** · 23rd January, 2016, 02:07 PM

Originally Posted by amir_82013

I install version 131 clip good but after a few days for opening software give me Error 15024 and 15028
What is problem ?
i check Interfaces = Good .
LED Interfaces = Good (Green and Red) .
Cable: USB & Prob = Good.
install again software = but not solved problem.

Please help me. it now can't connect to car.
Thanks.

I have the same problem. Did you decide this?

**yannou** · 7th February, 2016, 07:47 PM

Hello,
I'm french, sorry for my english...
I have a not bad clone can clip V127 with AN2135sc (with 2 green leds on) (automatic VIN is ok ). But it's not possible to update to actual firmware to V154. block to 74% (and 20% on other old clip version V132 for example).
I would like to know if its a problem on pcb can or iso. when can clip receive a new firmware, what is happening on pcb. Is it 2 firmwares ? one on ISO pcb and 1 on CAN pcb ?
is it possible to load firmware manually ?
any information are welcome
Yann

**speeddragon** · 23rd February, 2016, 02:38 AM

Hi guys, I've read this entire topic and I will try some things (mainly the oscillators), but still have a doubt related to my Renault Can Clone. The ISO green led isn't on. What could be the main reason for that ?

Thanks

**kenancatli** · 16th March, 2016, 11:35 PM

Hello
my Can clip not work iso light not on or binking
and 2 transistor or mosfet missing instead of diode! 2 normally diode solder by factory
which one mosfet or transistor 2 missing???
regards