VAG-COM/VCDS EVERYTHING

[pox]

Attachment 195434Attachment 195435
This is the interface. (VG.A 2010-04-08)
I made an Interface Test, and the result was K1-OK and K2-OK.

Hi

How to reflash Atmega on this board?
Is it enough to solder the SPI for Atmega?

[mattydr67]

Yes and power it up with 12V
Good luck

[Avf130]

Hello.Is there a guide in PDF how to update my VCDS 10.6 Cable to VCDS11.11 ?
What should i check ?

[telesfor]

instructions to upgrade to 11.11 but do not have the Poles who are looking for the installer loads, drivers, and user insnstalacji I put RAR.

[LPSERV]

I use parallel programmmer with 4 resistor, and work perfect....

[andrius]

if i teoreticaly have had a few dumps from org cabel with ft232RQ chip, is there a posibility to transfere that eeprom to cable with ft232BM cable and get it working? as even serial that depends on ft type is not correct and license will not pass without modification many thanks

[Avf130]

instructions to upgrade to 11.11 but do not have the Poles who are looking for the installer loads, drivers, and user insnstalacji I put RAR.

U have something in English ?

[BrendanT]

Please can someone help we with this!!! been trying to fine out if chinese clone cable 11.11.3 will work with the hex mp9 reset software...

i have been looking everywhere to see if anyone has tested this. thanks

[Chriss1981]

I have the 11.11.3 for ft232rl based interface without gal.

[avo3]

Helo mates,
I have one little question from where can I take working clone to update it to vcds the newest version. Would it be an good to buy it on ebay but what I should to write on the search field to get really working one or the best idea will be made one by myself. Could You give me some liks.
Which interface will be better:
http://www.ebay.pl/itm/LATEST-VAG-CO...item4610074e4d
or
http://www.ebay.com/itm/181155039749...ae8a05&vxp=mtr

Thanks in advance for the answer

[mattydr67]

Mate
Akk this new chinese tools working with 11.11.3 or with 12.10.3 beta are the one without GAL/ATF
So first of all it hasn't GAL/ATF and this is bad, no all functions activated.
Then the Chinese softwears are made to "kill" your tool not to protrect becasue they need to sell more not to make you happy.
The protection with firewall or to write 127.0...... into the HOSTS it is not a good solution for now.
So if want to have no problem in the fuhure you need to spend more money the 20-30 USD and you'll have a HQ clone and no internet problems at all.
But this you'll not find in the ebay for sure
Good luck

[magadan]

if i teoreticaly have had a few dumps from org cabel with ft232RQ chip, is there a posibility to transfere that eeprom to cable with ft232BM cable and get it working? as even serial that depends on ft type is not correct and license will not pass without modification many thanks

I write a loader in such cases . And the program starts working with it eeprom.

[avo3]

Thank You mattydr67 for Your fast answer but where I could buy this clone. Do You recomend some solution or web shop

[mattydr67]

Sorry mate
I cannot help you in this, I mean to recomand someoneelse or a web shop.
Good luck

[alexm1]

1.JPGDSCF1198.JPGDSCF1201.JPGIt is necessary , before reflahs, to remove some parts from this interface?
It is FTDI-BL and from what I read on the forum must stay how it is...
I am asking because I reflash it with 11.11 and after first autoscan became "unregistered".