Hello User, where can i get a good quality clone cable to use VCDS?
http://aliexpress.com/item/VAG-15-7-...rchweb201560_9
Is that a good deal?
http://www.digital-kaos.co.uk/forums...ight=atmega162
atmel
@jacob: led is red, why?
Must be Green. You power-up the cable? (+12V between pins 16 and 4 OBD2 or plugged in a car).
If not, that's the problemm.
And if LED is red when connect at usb, the cable is cheap and bad.
Few photos with both sides of PCB, good resolution.
@dadymee: loader is a little programm used for some versions of VCDS.
Hello User, where can i get a good quality clone cable to use VCDS?
http://aliexpress.com/item/VAG-15-7-...rchweb201560_9
Is that a good deal?
http://www.digital-kaos.co.uk/forums...ight=atmega162
atmel
Last edited by atmel162flasher; 21st November, 2015 at 02:08 PM.
Hi,
need some opinions..
In the pictures attached are 2 interfaces (1=old one 2009, 2= 2013) .
Nr. 2 has STC on pcb, because was "damaged by internet" I had to reflash Atmega to make it work, but without removing STC.
After first test it looks that it working fine.
So, is this type of interface(nr. 2) an exception that could be reflashed without removing STC chip? Or it is a matter of until will stop working(without internet " help")?
That stc is worthless. You'll be better of without it. It's no exception. There are others cables with stc that got the atmega162 data compromised. And in time the ft232BL won't work ok with that stc on the board.
I know that STC is worthless... but on the other side of PCB are signs that another STC (or something similar = 10 pads on 2 sides) was removed. See pic...
2 kind of "stc protection": like yours and like the other PCB.
Writing in atmega or in FTDI
alexm1 (24th November, 2015)
Hello, where can i buy a HQ Clone for VCDS 15.7.1?
I know www.sklad66.com, but sklad66 is much expensive.
Which chipsets use a HQ Clone?
Where can i see a board layout picture?
Greetz
atmel162flasher
hi guys Can I reflash this vag118 v 908 to 11.11 / 12.12
Image 001.jpg
Image 002.jpgImage 003.jpg
FoxMulder (26th November, 2015)
http://www.digital-kaos.co.uk/forums...=1#post2642775
Hard to search...
bravel digital (26th November, 2015)
I have a problem with 15.7 clone, with Atmega MCP2551 and TJA1050 STC chip inside. Cable work only with K line CAN is not working. I replace MCP2551 and TJA1050 but result was same, CAN not ready. My old 11.3 work perfect! Does anyone have schematic diagram or maybe solution for this problem?
Thanks
e10365d832c2aeafd4baa33be1c37c74.jpg
Delete few PM, inbox full
and look what mean search:
http://www.digital-kaos.co.uk/forums...CDS-EVERYTHING
Post #10
Last edited by liviudiaconu; 3rd December, 2015 at 07:54 PM.
Hello can someone please help with dump for gal for BL tool. My dog ate the gal IC.
Hey there,
I have a Chinese Vag11.11 interface, firmware 1.84, FTDI FT232BL, & Atmega 162. It reads and writes to the FTDI any .ept, so it's recognized and I can install any drivers for it.
The problem is it still shows up unlicensed. I'm not sure if I haven't had the proper .ept, or if the Atmega is damaged, and need to be reflashed. This past .ept I used (VCDSFT232BL.ept, from fantomels "1.VCDS COLLECTION") didn't return to the "this feature needs a registered copy" during auto-scan. It left me with:
interface check.JPG
Do I need to reprogram the Atmega for sure? I may just get a new interface since it was only $20, but if I can change the device to work with internet connected, as I've heard, I'm interested in learning.
I've included pictures of the device below, just in case. Thanks for your time.
IMG_0240.jpgIMG_0241.jpg
Last edited by tehnards; 15th December, 2015 at 07:00 AM.
Rewrite atmega with proper dump and use proper installer.
Bookmarks