VAG-COM/VCDS EVERYTHING

**Adyp** · 27th March, 2018, 06:39 PM

Originally Posted by Adyp

I have a Hex v2 (i know, old stuff with new coat) and with v6.3 loader I receive this message when autoscan:

This problem is only in 18.2.0, in 17.8.1 everything is OK! Any chance to make it work with 18.2.0?

**makadam** · 27th March, 2018, 11:53 PM

I tried to reprogram 2 pcs vag 15.7 using USBASP programmer but i get CHIP ENABLE PROGRAM ERROR ! I check connection twice tried to program both interfaces but same error.

IMG_20180328_004659_HDR.jpg IMG_20180328_004454_HDR.jpg

**1 6 D** · 28th March, 2018, 07:49 AM

I can't see that you solder to reset on pin4 od atmega162, there should be 5 wires, MISO MOSI SCK RESET GROUND

**liviudiaconu** · 28th March, 2018, 11:58 AM

For 15.7 "Red PCB with STC chip".
Even Kolimer said "No need desolder STC", i preffer to desolder it.

About Long Coding:

Can Gateway where Long Coding not documented well:
8T0 907 468 H
13.07.08

Can someone to confirm or infirm that?

Look at this photo;Attachment 517567

**makadam** · 28th March, 2018, 12:06 PM

Reset pin is connected but not on picture that I take. I tried several times without any success on both cables. But i updated firmware on this cable with same programmer. This cable works only with k line , can line is not ready! Any solution for that. Iam using 17.8 with v2 loader.

**BWF** · 28th March, 2018, 01:40 PM

Originally Posted by makadam

I tried to reprogram 2 pcs vag 15.7 using USBASP programmer but i get CHIP ENABLE PROGRAM ERROR ! I check connection twice tried to program both interfaces but same error.

IMG_20180328_004659_HDR.jpg IMG_20180328_004454_HDR.jpg

you have problems with the usbasp driver

**hid3** · 28th March, 2018, 02:19 PM

Originally Posted by Adyp

This problem is only in 18.2.0, in 17.8.1 everything is OK! Any chance to make it work with 18.2.0?

It's Ross-Tech's problems, not loader's problems.
They are promoting the sales of new interfaces.
Yet VCDS support for MQB cars sucks hard. The "support" they provide is nearly useless too.

**cyclop** · 28th March, 2018, 03:35 PM

Hello, would you be able to tell me if the cable pictured bellow can be reprogrammed? It's a version 12.12 with Atmega 162, ATF16V8b and FT232RL. Thanks.
VCDS.3-1.jpg VCDS.3-2.jpg

**Xaby** · 28th March, 2018, 03:53 PM

Yes it can be reprogrammed.

Sent from my D6603 using Tapatalk

**cyclop** · 28th March, 2018, 04:20 PM

Originally it came with 12.12, should I stick with the same version or I can load the latest dumps? Right now cable will read fault codes but I get unauthorized message. Yesterday I tried to release mu handbrake so I change my pads and it didn't work.

**alexm1** · 28th March, 2018, 06:52 PM

It is clear: it is Unregistered (See About), so it is not fully functional, if you have all you need reflash Atmega.

**makadam** · 28th March, 2018, 07:34 PM

Originally Posted by toglader

Finally got it working! First flashed atmega162 + eeprom and then ftdi with vagcom_eewritelang. Now self test passed but can is still not ok. Any ideas?

I have same problem with can, did u find any solution ?

Finally I reflash old 157 with colimer files install 17.8 using loader v2 and in all 3pcs (two red 157 and one old 904) is OK but works only modules with k line, CAN is not ready. I made a test with passat b6, Any solution?

About CHIP ENABLE PROGRAM ERROR BWF was right it was driver problem!

**Adyp** · 29th March, 2018, 08:23 AM

Originally Posted by hid3

It's Ross-Tech's problems, not loader's problems.
They are promoting the sales of new interfaces.
Yet VCDS support for MQB cars sucks hard. The "support" they provide is nearly useless too.

Thank you for your answer! So it's their software problem, they might do this to force old interface users to buy the new one...

**rivit** · 29th March, 2018, 09:14 AM

I want to use kolimer v6.3 loader. I downloaded 18.2.0 EN. My cable is 0x46.
How make it to work in polish language? Can i download 18.2.0 PL and is it all? in zip loader there another zip with lang files. Where i have to flash it?

ftdi_mprog_RLRQ is for FTDI232RL
Flash1.96_HW_0x46 is for atmega?
eepromavr_HW_0x46 this is for what?

I thought that i need 2 files to flash. one for atmega and one for FTDI.

One more question. If I use loader, can i use the internet during scanning?

PS. I read thread from ~300 page and i know how to connect it to programmer. Also i noticed that somebody told there's a possibility to program atmega via usb. is that true?

**alexm1** · 29th March, 2018, 09:24 AM

Most cases first time youl need to use usbasp.
For Atmega you need 2 files (mentioned by you eeprom+flash).
For Ft232xx different file.. ept
Read Pdf document(it is in the zip) for more info.