VAG-COM/VCDS EVERYTHING - Page 355
Register
Page 355 of 844 FirstFirst ... 255305345350351352353354355356357358359360365405455 ... LastLast
Results 5,311 to 5,325 of 12650
  1. #5311
    Newbie
    Join Date
    Nov 2017
    Posts
    6
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Hi,

    one more question before I connect the cable to 12V and try to reflash: Is it required to remove the STC chip? I have not modified anything on the cable, yet.

    Regards

  2. #5312
    DK Veteran

    Join Date
    Oct 2014
    Location
    Netherlands
    Posts
    1,716
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    849
    Thanked in
    612 Posts

    Default

    @Majami, using 17.8.0 EN can you check an UDS cluster and go to Adaptation channels and choose "staging" channel and see what is read?
    Several people get a "km" result and not "active" as it normally should be.

  3. #5313
    DK Veteran

    Join Date
    Oct 2014
    Location
    Netherlands
    Posts
    1,716
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    849
    Thanked in
    612 Posts

    Default

    The STC will reflash the ATMega it seems, so you need to remove it if you plan to upgrade yourself. Otherwise the STC will reflash back to some old version.
    You can simply remove 1 resistor (R50) but you can also simply remove all (STC+RESISTOR+TRANSISTOR).

  4. #5314
    Member

    Join Date
    Feb 2017
    Posts
    62
    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    1,033
    Thanked in
    49 Posts

    Default

    I can confirm that Beta 17.10.0 has some problems with CAN communication.

  5. The Following 9 Users Say Thank You to kolimer For This Useful Post:

    autodiagdoctor (16th November, 2017), H2Deetoo (16th November, 2017), ivica21 (25th November, 2017), jakuza (21st November, 2017), liviudiaconu (16th November, 2017), Majami (16th November, 2017), radsky (20th November, 2017), relax80 (19th November, 2017), tr3ce13 (16th November, 2017)

  6. #5315
    DK Veteran

    Join Date
    Oct 2014
    Location
    Netherlands
    Posts
    1,716
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    849
    Thanked in
    612 Posts

    Default

    Also 17.8.0 gives problems for several different users at least (UDS cluster adaptation f.e.)

  7. #5316
    Junior Member
    Join Date
    Jan 2017
    Location
    HongKong
    Posts
    31
    Thanks Thanks Given 
    6
    Thanks Thanks Received 
    5
    Thanked in
    4 Posts

    Default

    Hi, friends
    we have new ATMEGA162 HEX-V2, HEX V2 VCDS 17.8 full active cable For VW Audi Seat Skoda VAG HEX V2 support reprogramming, full chips : ATMEGA162 + FT232RQ + 9241 + 16V8B +ATA6561... Special thanks Kolimer for his support!!!
    HEX-V2-6c.jpg
    HEX-V2-7c.jpg

  8. #5317
    Newbie
    Join Date
    Nov 2017
    Posts
    6
    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Quote Originally Posted by H2Deetoo View Post
    The STC will reflash the ATMega it seems, so you need to remove it if you plan to upgrade yourself. Otherwise the STC will reflash back to some old version.
    You can simply remove 1 resistor (R50) but you can also simply remove all (STC+RESISTOR+TRANSISTOR).
    Thanks for the reply. In my case the PCB is not numbered and the resistors not numbered, which one is R50?

  9. #5318
    DK Veteran

    Join Date
    Oct 2014
    Location
    Netherlands
    Posts
    1,716
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    849
    Thanked in
    612 Posts

    Default

    In that case I suggest to remove the STC completely, don't worry about the other components.

  10. #5319
    DK Veteran

    Join Date
    Oct 2014
    Location
    Netherlands
    Posts
    1,716
    Thanks Thanks Given 
    269
    Thanks Thanks Received 
    849
    Thanked in
    612 Posts

    Default

    @kolimer:

    I am working on VCDS protocol and I might have a small improvement to your tool EEType.
    As you know sometime the AVR doesn't respond when requesting fw version.

    It is mentioned here the cable must be "unlocked".
    But in fact this is because cable is in some other mode (lets call it "canbus" mode).

    You can send the following command to put the cable back in "command" mode :
    -> 53 04 A0 F7
    <- 4D 04 FE B7

    After you sent this command you can request firmware version again

    Also, for completeness, the following command will put the cable back in "canbus" mode:
    -> 53 04 B0 E7
    <- 4D 04 FE B7

    Feel free to contact me to discuss this protocol if you're interested.


    Rgs H2Deetoo

  11. The Following User Says Thank You to H2Deetoo For This Useful Post:

    seal777 (24th February, 2019)

  12. #5320
    DK Veteran
    Join Date
    Feb 2013
    Posts
    392
    Thanks Thanks Given 
    73
    Thanks Thanks Received 
    94
    Thanked in
    77 Posts

    Default

    Hi,
    There is possible to run vcds software from PC (NR.1) with the cable plugged into another PC(NR.2) using a internet connection with a remote/vpn software like Teamviewer?

    Same questions for flashing Atmega via usb in the same situation: interface connected on PC NR.1 and running software(VAGCOM_EEWRITE) from PC NR.2? Pc.s conected togheter via a wirelles network using Teamviewer or another software?

  13. #5321
    Newbie
    Join Date
    Jun 2010
    Posts
    1
    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Default

    Hi forum!

    I'm looking into buying a VAG-COM cable for my 2016 Skoda Superb, but I dont want to spend $199 for a cable.

    Since it looks like there are many bright heads here, is there a cable you can recommend? I'd like to use Ross Tech VAG-COM 17.8 - need a cable to which is compatible with this software.

  14. #5322
    DK Veteran

    Join Date
    Apr 2013
    Posts
    468
    Thanks Thanks Given 
    81
    Thanks Thanks Received 
    140
    Thanked in
    93 Posts

    Default

    Look post #5316 for example

  15. The Following User Says Thank You to 2xded For This Useful Post:

    T_ac_S (19th November, 2017)

  16. #5323
    Top Poster +
    Join Date
    Sep 2009
    Location
    Spain
    Posts
    228
    Thanks Thanks Given 
    49
    Thanks Thanks Received 
    17
    Thanked in
    14 Posts

    Default

    hi i need help vcds loader blocks 91% in Windows 8.1,
    i have uninstalled vcds loader and vcds 17.1.3 remains the same.


    Captura.JPG

  17. #5324
    Newbie
    Join Date
    Jan 2017
    Posts
    7
    Thanks Thanks Given 
    8
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    Talking

    Quote Originally Posted by pacomasi View Post
    hi i need help vcds loader blocks 91% in Windows 8.1,
    i have uninstalled vcds loader and vcds 17.1.3 remains the same.


    Captura.JPG
    Wrong theard, we talk about Kilomer Loader and not China garbage.
    Forget Windows 8 and 8.1

  18. #5325
    Junior Member
    Join Date
    Jan 2017
    Location
    HongKong
    Posts
    31
    Thanks Thanks Given 
    6
    Thanks Thanks Received 
    5
    Thanked in
    4 Posts

    Default

    Hi, you could try use newer vcds loader v1.10 to try , EST software this period not work very well, waiting for update newer

 

 

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.