The video in the link shows the connection at 1:27 - https://www.youtube.com/watch?v=wcYb_Zzk_VU
However, This may be of some info to you http://www.digital-kaos.co.uk/forums...s-with-carprog
Hello friends
I’m new in carprog i have 2016 nissan altima with crash data module (98820-9HS0A) XC2336B40 .
Fristly, how can i read cash data from airbag module which unit and program use?
moreover i have carprog 10.93 with full units but i dont know how can use it and what is the cable need ,what is the circuit to connect with eeprom???
anyone can help me by pic ?
thanks
The video in the link shows the connection at 1:27 - https://www.youtube.com/watch?v=wcYb_Zzk_VU
However, This may be of some info to you http://www.digital-kaos.co.uk/forums...s-with-carprog
hello, in carprog v8.21 no mini cooper, maybe is update?
hello.I have successfully updated my carprog from 081105CAR001773I to online version 8.21. Now I have only one error with D1 adapter.
Carprog alone + A9 pass the test OK.
Carprog + A1 pass Test ok.
Carprog + A9 in Test D1 = all ok.
Carprog + D1 + A9 in Test D1 say errors
UART1: ok
K Line 100k/5v: ok
K Line 1k/5v: ERROR
K Line 1K/12v: ERROR
K Line 100K/12v: ERROR
Attachment 562289
Does any one know the value of the capacitor in the green box? My capacitor reads a zero value...
Dashboard Fiat 500 obs II - I get an error while reading.
Unit CRC error: Delete LIB file ....
Sn: 150428CAR00577RU
Last edited by MrBingo; 12th October, 2018 at 10:56 PM.
erniss14 (20th October, 2018)
Hello,
I've got problem with my carprog clone 8.21 online. It doesn't read eeprom - shows only 00 values and when I'm reading ECUs by OBD (A1 adapter) it shows wrong values Immo PIN. I changed all 74HCT125 and crystal quartz. Carprog passes all tests.
Hello mates, I wanna ask one thing, carprog 8.21 clone have all function activated?
Best regards
Remember thanks and reputation buttons if helped
Hello ! I, like everyone else, have problems with my Carprog antenna. Chinese Clone Version 8.21. I read tons of antenna repair information. I did all the known corrections so far. Htrc110 was defective. After the replacement, I tried again Chinese antenna, antenna from VAG but the results were unsatisfactory. On a sample of different antennas, I re-calculated the resonance frequency of the LC group. I found info and made my own antenna. As a result, he began to read partially VAG transponders.I test with ready and runnig keys from pasat b5 and fabia mk1 with transponder Id48. I have no trouble to reading ID and UM1 , but when reading UM2 have error weak signal from transponder . Both transponders are locked.With locked transponder should I read UM2? What is UM2 and can I add a new key without reading UM2 ? On the PCB I make the following adjustments - I cleaned a PCB ,replacing the 74HC125D with MM74HC125M, replacing the HTRC11001T, soldering the whole board and other minor corrections. The board is with firmware 150731CAR00064RA . I do not see how to apply photos. Anybody have an idea on the subject?
Thanks !
Press Thanks and Reputation
kebappa (31st October, 2018)
I have done these procedures by calculating capacitors, resistance of the whole antenna (including the grenator), current through the antenna during reading and recording. The problem is that everything is calculated and the antenna can read the transponder to the end. I have tried with other values, but my greatest success is reading the ID and UM1 of ID48 transponder.
I’m trying to clear crash data for tms320 Honda module. Carprog are not replying to my email about buying airbag activation for the legit programmer so I’m using second one that is a clone.
I keep getting “connect d1” error.
( D1 was repaired with upgraded components tho. )
Bookmarks