I think in this car immo is incorporated in body control module, can't be removed separetly... just need to cut immo line and connect black/yellow wire from starter relay to GND...
i'm trying to make a immo off on a freelander year 2000 diesel with a bosch 0281010113 ecu msa 11
immo decoding tell me to program both 93c46 eeprom and disconnect the immo box and splice togheter yellow and black wire
where's immobox on this car!?!?!?
please help me!
ProTuner since 1999
I think in this car immo is incorporated in body control module, can't be removed separetly... just need to cut immo line and connect black/yellow wire from starter relay to GND...
atomiczen (9th October, 2013)
hi shmortz, i have ear that it's possible to immo off this car switching the 2 dil for 50 seconds with ign on or removing one of the 93c46
immo dec 3.2 tell me to program both 93c46 remove trasponder and splice togheter yellow and black wire, info isn't too clear....where are these yellow and black wires???
i have to cut immo line from ecu or from body computer?
antenna must be connected or not? there's 2 antenna on this car, one over the dash for the remote control, and one ring into the ignition switch
where's starter relay?
please help me because i become crazy with this car
ProTuner since 1999
for who need i have found a solution here on forum
remove the 93c46 near the yellow capacitors then cut pin 45 to the ecu
tomorrow i'll test and report
ProTuner since 1999
KILL_THE_IMMO (4th May, 2015)
problem solved, thanks to stoyanov and shmortz, problem was mine, i forgot to connect black/yellow wire from relay to ground
dk forum is everytime the right solution!
ProTuner since 1999
thanks for sharing. i?ll post result soonly.
please e need one more help. i need pinout to know pin 45 and i need to know the location of the starter relay. regards
alclot (24th December, 2019), alejandrobr1995 (6th June, 2018), bangreno (21st November, 2018), danielif (6th October, 2023), dantetimoc (3rd May, 2023), daquima (24th June, 2023), gopelhu (28th January, 2021), H.Wessel (10th February, 2022), Jacob6969 (31st March, 2021), kronk92 (28th February, 2021), Rotor (23rd August, 2018), Serg1o (11th April, 2020), taythephoenix (27th September, 2022), Truan21 (8th April, 2021), vavrich (30th October, 2020), wolfoyo (13th December, 2017)
i try this solution today
Immo off ecu msa 11
1.Remove the 93c46 near the yellow capacitors.
2.Cut pin 45 to the ecu.
3.Connect black/yellow wire from starter relay to ground.
alejandrobr1995 (6th June, 2018), andrey3 (9th July, 2019), CaioW (23rd April, 2018), danielif (6th October, 2023), dantetimoc (3rd May, 2023), daquima (24th June, 2023), giani67 (4th September, 2020), gobe (12th June, 2019), H.Wessel (10th February, 2022), Jacob6969 (31st March, 2021), jmgameiro (20th March, 2022), marius7592 (16th December, 2021), tato10 (31st October, 2018), tellfaia (15th January, 2024), Truan21 (8th April, 2021), vavrich (30th October, 2020), wflseba (12th January, 2023)
trinicolin (22nd March, 2021), vavrich (30th October, 2020)
ben yapamadım tam olarak epromu sökmelimiyim bana detaylı yaprdımcı olurmusunuz
brend (27th October, 2018)
hello guys. i need help locating the black/yellow wire from starting relay. could you please tell me where is located? thank you
+thanks if I helped you!
Bookmarks