Try to rewrite the ucontroller.be ware it's secured.here is an empty contetnt fron a new brand one but the ucontroller is s12d256.
Hi friends, Somebody know if I can repair this module? ELV is dead, car not start, I can make diag only on CAN gateway. I remove the module from car and if I push one switch from pcb, car start. If I put 12V to stering lock motor, works. Lock/unlock stering.
reference:
HW: 4F0 905 852B
3.0
SW: 4F0 910 852
01.30
on PCB I have MC9S12DG128 mask: 3L40K
Thanks
Geza
Try to rewrite the ucontroller.be ware it's secured.here is an empty contetnt fron a new brand one but the ucontroller is s12d256.
ASCM (7th June, 2020), AVDIMON (29th April, 2016), bmc (6th December, 2019), bokilee (15th January, 2019), br.balazs (8th February, 2015), chefdediag (17th April, 2017), dzevad (24th December, 2020), feketezsolt (6th April, 2017), Geza (19th February, 2016), kojara (17th August, 2013), koki (18th January, 2016), ktome (22nd November, 2020), owdi (12th September, 2021), paulotxr (19th February, 2022), powered by (18th May, 2017), puntt (3rd January, 2018), sazimam11 (16th October, 2019), tomo776 (17th February, 2018), toms4 (7th January, 2016), vanos batam (4th July, 2023), vasa (14th September, 2019), xifly18 (9th December, 2015)
Is it a locked processor? Can I read it with Omega?
If I rewrite the processor, how can I adapt the ELV?
Last edited by znoki; 24th May, 2012 at 08:17 PM.
jjas40 (13th September, 2016)
hello
help for 3l60k motorola
you have read this motorola?
thanks
luigi
read ok with rosfar r260 tested
Hi,
I've got same problem again, but the processor is 1L59W - MC912DG128.
4F0905852B, 3.0 , index: 01.60
Have somebody similar virgin file as illestibor for my processor? (because I need only 2048 byte eeprom file)
Cheers!
even though 2 legs from 8 are not bonded, a spider is a still spider (93c86)
yes here is what did you like
for password chek pm
alexjpjp (21st June, 2016), AVDIMON (29th April, 2016), baskom (25th January, 2018), clearly (16th May, 2019), ettaoussi (30th January, 2015), ktome (22nd November, 2020), line44 (28th September, 2017), mariokn (3rd December, 2013), mhz2005 (16th May, 2017), toms4 (7th January, 2016), wokounek (24th March, 2015)
Hi Jokersat,
Thanks for your file, I checked it, but I found a VIN number. Is it virgin?
What should I do? Reprogram the eeprom area, and than? Online coding? Synchronisation?
Somebody else said, I should erase and reprogram the flash area. What do you think? Do you have the flash file too?
Cheers!
even though 2 legs from 8 are not bonded, a spider is a still spider (93c86)
mariokn (3rd December, 2013)
Read eeprom+flash by xprogm and put to new (used) elv
Good luck
even though 2 legs from 8 are not bonded, a spider is a still spider (93c86)
sometimes xprogm v5.0 broken elv. Better use oryginal. working 100%
problem is flash dump
sometimes if swap ori mcu to second elv can work and somtimes dont work then the problem is flash dump
tested 100/100
Ok, I understand, but I think I can erase only the flash by MTRK and rewrite it. Is it not enough?
even though 2 legs from 8 are not bonded, a spider is a still spider (93c86)
slivovica (18th November, 2017)
pls dont use mtrk omega or orange use xprog m or rosfar to read this mcu
omega orange dont work with this securised mcu
@+
clearly (17th May, 2019)
Bookmarks