I think XTOOL can
I add by SKP900 very easy by PIN extract from BCM
Hi. Can xtool pad2 add spare key for usa volt 2014
Key like this.
sav few videos that possoble add apare without any tools. Just when have ori key.
Turn ignition on wait till immo light gone. Than put new key turn ignition and it automaticly programs to car.
http://fkmedia.transponderislan.netd...tik-chv-44.jpg
I think XTOOL can
I add by SKP900 very easy by PIN extract from BCM
I surprise those who do not want to use the Thanks and Reputation buttons but ask for the password of the files.
drugowaz (11th October, 2017)
how about that trick without tools? by changing ori and spare new key?
1 method :
1. Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave
the key in the “ON” position for approximately 11 minutes. The security light will be steady
on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light
turns off or stops flashing.
2. Turn the ignition switch to the “OFF” position for 30 seconds.
3. Turn the ignition switch to the “ON” position as in Step 1 for 11 minutes.
4. Turn the ignition switch to the “OFF” position for 30 seconds.
5. Turn the ignition switch to the “ON” position as in Step 1 for 11 minutes for a third time.
6. Turn the ignition switch to the “OFF” position for 30 seconds for a third time.
7. Turn the ignition switch to the “ON” position for 30 seconds.
8. Turn the ignition switch to the “OFF” position.
9. Attempt to start the engine.
If the engine starts and runs, the relearn is complete.
2method :
1. Turn ignition on.
2. Attempt to start the engine, and then release the key to the “ON” position.
3. Observe the “SECURITY” indicator light. After 10 minutes the “SECURITY” indicator light
will turn off.
4. Turn ignition to the “OFF” position, and wait 10 seconds.
5. Attempt to start the engine, and then release the key to the “ON” position.
6. Observe the “SECURITY” indicator light. After 10 minutes the “SECURITY” indicator light
will turn off.
7. Turn ignition to the “OFF” position, and wait 10 seconds.
8. Attempt to start the engine, and then release the key to the “ON” position.
9. Observe the “SECURITY” indicator light. After 10 minutes the “SECURITY” indicator light
will turn off.
10. Turn ignition to the “OFF” position, and wait 10 seconds.
11. Vehicle has now learned the new password. Start the engine.
12. With a scan tool, clear any trouble codes.
NOTE:
For most cars, one 10-minute cycle will be enough for the vehicle to learn the new
password. Perform all 3 cycles if the car will not start after 1 cycle. Most trucks will require all
3 cycles for learning the password.
3 method :
1. Insert a master key (black head) into the ignition switch.
2. Turn key to the “ON” position without starting the engine. Security light should turn on and
stay on.
3. Wait for 10 minutes or until the security light turns off.
4. Turn key to the “OFF” position for 5 seconds.
5. Turn key to the “ON” position without starting the engine. Security light should turn on and
stay on.
6. Wait for 10 minutes or until the security light turns off.
7. Turn key to the “OFF” position for 5 seconds.
8. Turn key to the “ON” position without starting the engine. Security light should turn on and
stay on.
9. Wait for 10 minutes or until the security light turns off.
10. Turn key to the “OFF” position. The key transponder information will be learned on the next
start cycle.
11. Start the vehicle. If the vehicle starts and runs normally, the relearn is complete. If additional
keys need to be relearned:
12. Turn the key to the “OFF” position.
13. Insert the next key to be learned. Turn the key to the “ON” position within 10 seconds of
removing the previously used key.
14. Wait for security light to turn off. It should happen fairly quickly. You may not notice the
lamp, as the transponder value will be learned immediately
15. Repeat steps 12 through 14 for any additional ke
Good job
I surprise those who do not want to use the Thanks and Reputation buttons but ask for the password of the files.
Checked car list in pad2 no volt model. Under what other model possible to add key?
drugowaz (12th October, 2017)
If run as all keys lost. Old original key will be programmed too? As i need just spare
if clone.remote will not work. who want this type of key without remote
in my country.99% want full key. 1 of 20 choose only service key.
answer is eeeaaaaa i need to lock door with hand?? eeeaaa neeeaaaa.
p1et (23rd October, 2017)
I dont say they do full key . Mostly frice is to high. But they rather dont choose do spare key at all . Cars like volt or more expensive from usa they all want full key. This year ive done maybe 2 or 3 keys without remote. All other full keys
Bookmarks