X6/V8 Key Code Cutting Machine

**klesk1986** · 11th March, 2018, 04:33 PM

This one in pc codemaster software works good for cutting - I decode by eye

**auto techniek** · 11th March, 2018, 04:36 PM

I have to practice a lot

Do you have any probems cutting hu64? Does not work good for me. 8 from 10 times key don't open doors.

Originally Posted by klesk1986

This one in pc codemaster software works good for cutting - I decode by eye

**rob h** · 11th March, 2018, 11:00 PM

There a 3 types of hu64.
Try this: cut the key, then take 2mm off the tip.

I assume that you can decode any key correct.
Firts cut to tip, 5.8mm, when you cut it.
Taking the 2mm of, 3.8 to tip. this will fix it.

Originally Posted by auto techniek

I have to practice a lot

Do you have any probems cutting hu64? Does not work good for me. 8 from 10 times key don't open doors.

**darknezz19** · 13th March, 2018, 05:57 PM

Had to cut a KIA Optima 2011 KK8 blade but it's not in my x6v8 database, nothing in Hyundai or Kia matches it. It's close to 8.8mm wide on a blank blade, HY15 is 8.3mm and when cut using that profile it kinda worked but it's not the right profile. Anyone have the profile specs for this KK8 key so we can manually add it in? My Instacode doesn't list this key profile either.

**camelgd** · 13th March, 2018, 09:11 PM

From Mike Hyde's Auto Smart Book, (2012 newest I had at hand) KK8, Spaces: .795, .713, .630, .547, .465, .382, .299, .217 (.083 cut to cut)
5 Depths: 1=.328 2=.308 3=.289 4=.269 5=.249
Macs: 3
Sorry they are in inches instead of mm.

**rob h** · 13th March, 2018, 09:18 PM

KK8 is ilco= silca HYN14RTE
It is 8.4mm, it should be in the menu.

Originally Posted by darknezz19

Had to cut a KIA Optima 2011 KK8 blade but it's not in my x6v8 database, nothing in Hyundai or Kia matches it. It's close to 8.8mm wide on a blank blade, HY15 is 8.3mm and when cut using that profile it kinda worked but it's not the right profile. Anyone have the profile specs for this KK8 key so we can manually add it in? My Instacode doesn't list this key profile either.

**darknezz19** · 15th March, 2018, 12:56 AM

It's weird because these kia KK8 blanks are 8.7mm wide on the uncut blade. Some of the cuts on the customers keys were 8.7mm or a little below but no where close to 8.3mm. HYN14 was close but not even the spacing was the same. Used key duplicator machine to finish copy and hopefully can figure this out before a an all key lost job calls.

**darknezz19** · 17th March, 2018, 01:17 AM

Crap, broke a belt. Had replacements ordered before this happened but distributor canceled on me because the were out. Anyone know where to get 153mxl state side or does anyone have one I could buy? Trying to use a tube tire repair patch to make the one I have work hopefully till replacement gets here.

**super jumbe** · 30th March, 2018, 12:23 PM

Getting to think twice, I will wait another 6 months before deciding to buy from what I have read its a crap machine...

**Buddy41** · 8th April, 2018, 12:34 PM

sorry my mistake

**ibratex** · 31st May, 2018, 12:13 AM

hello mates how to use x6 v8 to cut hu101 rover key please guide me any video oit there thanks in advance

Sent from my SM-G935F using Tapatalk

**auto techniek** · 1st June, 2018, 02:55 PM

Guys

I made a lot Hu66 keys without problems
Today need make key for Seat Leon 2007. Made 3 key but none of them turned the ignition on.
I used HU66 H8 to copy.
At the begining of the key you can see the difference.

**darknezz19** · 7th June, 2018, 03:39 PM

Originally Posted by auto techniek

Guys

I made a lot Hu66 keys without problems
Today need make key for Seat Leon 2007. Made 3 key but none of them turned the ignition on.
I used HU66 H8 to copy.
At the begining of the key you can see the difference.

Mine did the same thing yesterday. Cut a test key and it worked great, then when trying to cut the flip key blade it offset lower just like yours. I didn't use the HU66 adapter but will try again with it today.