teerak2uk (2nd January, 2017)
Sorry, I did not realize my mistake, it will not happen again.
PS1; Many friends have problems because they did not buy Digiprog 3 with the FTDI chip, it is responsible for the communication between Digiprog and PC, you can use Digiprog connected to the PC and use EEtool software
ps2; You can request help from the experts by posting the Digiprog file and requesting the modification of the file
teerak2uk (2nd January, 2017)
I think so. But enigma i am still confuse it is good or not.
kubuswujo (3rd January, 2017)
I have bought a USB UPA and will try to do it with it. Because my DigiProg 3 doesn't have FDI CHIP and i cannot connect it with computer, and keep restarting when I do WRITE on EEprom.
Any suggestion before doing it with USB UPA Eeprom Programmer? Which program beter to use. which adapter? It will be my first Eeprom programming.
2014 polo 1.2 TSI dash.jpgWould it work on the 2014 and 2015 models with the same cluster as per picture perhaps i.e VDO NEC +24C64 like golf 6 and amarok 2010- dash via ob
Last edited by rtbdiagnostic; 3rd January, 2017 at 02:40 PM.
'If I helped, please click Thanks +Reputation.. !'
Hi everyone!
can someone tell me how to connect the Dash from Toyota Prius II C66 2007/8 with USB UPA?
Now i have soldered the adapter from DIGIPROG3 (green wire is allready desoldered).
And using the same points i want to connect it with USB UPA to flash Eeprom manually, but cannot find .pdf what connectors are what.
On the picture is USB-UPA with adapter that in my opinion suits 93CS66 witch is Toyota Prius II.
Can someone give a solution.
please?
IMG_20170103_221049.jpg
IMG_20170103_221133.jpg
I have desolder a screen and using multimeter looked for a pins/connector and...
Fore those who will need is in the FUTURE:
Looking for my last picture the pins are:
1-RED
2-Free
3-BLUE
4-BROWN
6-YELLOW
5-WHITE
the pins 7 and 8 are not on that side of board, and I had to solder them directly on pins on 93C66 x16.
(BTW. How enigma, and DIGIPROG changes Milage without that pins? USB UPA hadn't write/verfy good chip without pin 7.
So ok my original data was:
Toyota Before.JPG
And than i change the 2 lines :
000
010
020
To milage E3 2B = 191 000
But when I done PROGRAM/WRITE and than READ it shows me:
Toyota after.JPG
The lines that I change are ok but there are some FF which weren't there before......
Is that ok? those FF??
Or can i already go with tacho to car and instal it?
Or probably I can Power it up with pins on table, but which one?
EDIT:
On Usb-UPA I used 93C66 x16 instead of 93C66 beacuse on 93C66 i had errors, so that chip is 16 bit, am I right?
EDIT 2:
I have find how to power up TACHO, pins are:
14- GND
22- 12V+
I have power it up and it's blinking but the milage is not corect, its 1_ _ _ 96
I wanted 190 000
IMG_20170105_023034_HDR.jpg
>>>> Should I REProgram it one more time? changing those FF to 00??? <<<<
Last edited by kubuswujo; 5th January, 2017 at 02:48 AM.
kubuswujosorry to say that but you really complicate your life i sayed read eeprom with digi save fle . go to write eeprom change the lines that you have corrected with tachosoft manually and write. thats all no need foe upa or other tools and you dont need to connect with PC its a question of common sence .just begin with what i told you and it wil be ok.let us khnow and BTW the first read with DIGI is never good it give a non logical value just write and it wil be ok no need to do it with tachosoft actually i have done a couple of these.
Last edited by garabounga; 5th January, 2017 at 09:18 AM.
memet99600 (5th January, 2017), Rhogan (5th January, 2017)
As I sad before i cannot do it with DIGIPROG3
Because when i do WRITE it keeps restarting!!!! I tried to do it by CAR>MODEL LIST>>
and by Eeprom
Eeprom Verify>Write.
So in my opinion I cannot use DIGIPROG If it not working properly. (RESTART After begining of writing)
Can someone ask to my questions from post before?
Ok use the same pinout like digi with upa but i think your display is not good if the calculation was wrong you couldnt see numbers only ------- your display is kapot put it in car and look if you get all the numbers displayed look if the display pins are good solderd and BTW you wil never get precies 190.000 its always 190.069 or some thing like that its for sure display not good correction is ok
Last edited by garabounga; 5th January, 2017 at 01:03 PM.
kubuswujo (5th January, 2017)
Ok I will try to resolder it one more time (display). I wanted 191 000 and ok if it is for example 191096 km (I also thought that it will not be equal, but thanks for explaing).
So no i should buy another tacho, as i think and should I program data from ~~~~ginal tacho 93C66 to new one? Is it enought?
Shouldn't I do any adaptation or IMMO? Is ther IMMO In Tacho?
honingkoning (5th January, 2017)
No no adaptation needed and no immo just look if the solder points are good dont program any thing now the mileage is good just check solder points it wil be ok if not just buy another tacho and be carefull as its a schity job to get this dash uit pfffffffff
kubuswujo (5th January, 2017)
En is it solved?
Hi guys,
i found this offer Digiprog 3 v4.94 with FTDI Chip for 167 $
what do you think? any info about the quality sold by this seller?
any reliable seler who sells good quality digiprog for low $$$?
thank you guys
Rhogan (8th January, 2017)
Hello, Abdulsattar, I bought a Digiprog c / ftdi from the store https://pt.aliexpress.com/item/Digip...ryId=200000377 I have not received my order, but as soon as I receive it naturally I will post here in the forum about quality, until this moment the service was Good seller Laura
abdulsattar (9th January, 2017)
Bookmarks