VVDI PROG

[morito]

thank you friend,checked dump,this programer use the default low baudrate 9600bps to read data.
VVDI PROG changed baudrate to 153600bps to decrease read time
baudrate change step:
1.Use low baudrate 9600 wakeup the chip, if get the correct response,go to step2
2.Start change baudrate, due to the d70f3624 doesn't know own osc frequency,programer need send it the accurate value
(VVDI PROG put some common-used osc value,so you can see try frequency xxxxhz info)

3.Programer send the new baudrate value to d70f3624, vvdiprog use 153600bps
the d70f3624 can calculate the new baudrate with the osc value, but if the osc value is incorrect,you will get a wrong baudrate
(eg: the actual osc is 4Mhz, if you set a 8Mhz osc value and change the baudrate to 153600bps the chip will set a 76800bps)
4.Use the new baudrate to communicate

Maybe the osc frequency is not in VVDI PROG osc value list
Please grab a new dump with vvdiprog,need to further analyze of the problem.

hi
I have same problema whi d70f3630 frequency error.
can somebody explain the SAMIC process I do not understand it well

MAny thanks in the advace

[dorofteius]

Tested today M35080v and 080d0wq . It erases perfect.
Thank You Samic and X-Horse team.

[chli1976]

Tested today M35080v and 080d0wq . It erases perfect.
Thank You Samic and X-Horse team.

Also the first two lines ?

[dorofteius]

Yes mate. Also the first 2.
That is the idea .

[gilahish]

Tested the pin calculator -
Nissan BCM - not good, gave me 2 digits and 2 letter instead of 4 digits only.
Hyundai VIN TO PIN - not good, gave me 8 digits and letters instead of 6 digits only.

[nickolasd]

i checked mine it did erase 080d0wq but it failed to erase original from bmw dash 35080VP

[aceton]

I think this is fake.
First time i ask him month ago.
In every @ he says that you must wait 2 days.

[dorofteius]

I erased the m35080 from e65 dash.
With the option 35080 old, that exist only in the last version of vvdi-prog.

[haiz0708]

Hi Mate,

Need some guide, May I know VVDI prog can unlock the BMW Cas3 Key (china) which is PCF7941?
I lost the Cas3 eep data, now key is lock.

[automotrizVIP]

Hello to all, some to insircuitado memories of 6 pin 93cxx?

[Levanime]

Hi Mate,

Need some guide, May I know VVDI prog can unlock the BMW Cas3 Key (china) which is PCF7941?
I lost the Cas3 eep data, now key is lock.

I have not tried china board but original board was fine, it also has china board in list

dont forget to unsolder battery if its non CA key

[dmp]

I have not tried china board but original board was fine, it also has china board in list

dont forget to unsolder battery if its non CA key

Have you had success renewing a ca key?? I've only tried two and neither worked (on board). They programmed to the car but remote didn't work

Sent from my SM-G930W8 using Tapatalk

[automotrizVIP]

The following mistakes does anyone pass the same?
mcu ford fiesta mcu mcu9s12hz256 no read set Frequency UPA OK
memory eeprom 8pin read bad 95320 (FF FF). UPA OK
memory so23p 6 pin error read y write.

[eagleone-two]

Audi A6 ELV (J518) ---2010 not working correctly. Flash read ok but eeprom each reading is different. Please correct it.


Wysłane z iPhone za pomocą Tapatalk

[AutoKeyGuy]

Read EEPROM of 2008 Mercedes Sprinter (W906) successfully