View Full Version : XPROG-M DAMAGE
kasim_izmir
12th March, 2010, 10:06 AM
Hi to all m8
Please can you help me ? I need to know xprog-m all IC's .
I will make to repair of my xprog-m
Give me error while reading eeprom(bad contact at 5,6,8) and MCU (device is silent)
please see picrutes in attach
WBR
kasim
parapilot
12th March, 2010, 11:06 AM
have you tried to select the right COM port? Under options - environment? i notice different com numbers on your pictures.
Check the connections on the eeprom to.
Cheers
J
kasim_izmir
12th March, 2010, 11:09 AM
have you tried to select the right COM port? Under options - environment? i notice different com numbers on your pictures.
Check the connections on the eeprom to.
Cheers
J
YES M8
I CHECK RIGHT COM PORT. I CHECK ALL 5 VOLT
I USE USB (NO NEED 12 VOLT ) PROBLEM IS SAME ... E.G I CAN'T READ HC912B32 WITH XPROG-M .. THEN I CONNECT TO UPA READ AND WRITE SUCCESSFUL
I USE DB9 PROBLEM IS SAME
WBR
kasim
branco
12th March, 2010, 02:08 PM
YES M8
I CHECK RIGHT COM PORT. I CHECK ALL 5 VOLT
I USE USB (NO NEED 12 VOLT ) PROBLEM IS SAME ... E.G I CAN'T READ HC912B32 WITH XPROG-M .. THEN I CONNECT TO UPA READ AND WRITE SUCCESSFUL
I USE DB9 PROBLEM IS SAME
WBR
kasim
buy original
is better
or change usb cable
regards
kasim_izmir
12th March, 2010, 03:45 PM
buy original
is better
or change usb cable
regards
Thanks for advice ;)
I connect rs232 cable problem is same :questionmark:
PROCESSOR
12th March, 2010, 04:29 PM
Hi,
you need to change one of the 2 ic near the dip8 socket , i think is 74HC244D.
Best REGARDS.
kasim_izmir
13th March, 2010, 09:41 AM
Hi,
you need to change one of the 2 ic near the dip8 socket , i think is 74HC244D.
Best REGARDS.
Thank you , i will change theese 74hc244d.
BTW, I am thinking , maybe 64pin mcu damage , but i don't know what is this mcu
WBR
kasim
serg777
13th March, 2010, 10:19 AM
may be connect moda modb
kasim_izmir
13th March, 2010, 11:30 AM
Hi,
you need to change one of the 2 ic near the dip8 socket , i think is 74HC244D.
Best REGARDS.
Hi m8
I replaced 74hc244 . problem is same, Have you another idea
Thanks in advice
kasim
kasim_izmir
13th March, 2010, 11:34 AM
may be connect moda modb
No friend , i use xprog-m everyday. connect only 4 cable for read hc912b32. also , can't read eeprom via DIP8
BTW , WHO CAN SEND SCHEMA FOR REPAIR XPROG-M :)
BR
kasim
umoussa
14th March, 2010, 02:07 AM
Hi Kasim
Maybe i know you from one of my friends in Ankara??
Anyhow, have you tried to update the software of the X-Prog recently?
If yes, then this is the reason.
If you know my friend in Ankara, then contact him, he'll guide you, he had the same problem :)
Thank you
Umoussa
kasim_izmir
15th March, 2010, 07:10 AM
Hi Kasim
Maybe i know you from one of my friends in Ankara??
Anyhow, have you tried to update the software of the X-Prog recently?
If yes, then this is the reason.
If you know my friend in Ankara, then contact him, he'll guide you, he had the same problem :)
Thank you
Umoussa
Hi, Thanks for advice
I am not try to update never ...
I will buy xprog new one ..
BR
kasim
another_seller
15th March, 2010, 07:11 PM
Hi to all m8
Please can you help me ? I need to know xprog-m all IC's .
I will make to repair of my xprog-m
Give me error while reading eeprom(bad contact at 5,6,8) and MCU (device is silent)
please see picrutes in attach
WBR
kasim
hi, Kasim, can you send to me a clearer picture on the errors ? maybe i know some hints ...
kasim_izmir
16th March, 2010, 12:03 PM
hi, Kasim, can you send to me a clearer picture on the errors ? maybe i know some hints ...
Hi friend
Part of the problem was solved.. I read and write motorola MCU.
I can't read and write serial eeprom only
I try to read 25320 give me error as 1,2,3,5,6,7,8
I try to read 24c02 give me error as 4,5,6..and 93cxx is same
And always different errors, If i select eerprom from other Manufacturer
WBR
kasim
Zmann
16th March, 2010, 06:29 PM
I've never use xprog-m but if its possible try to forward series a diode to the eeprom vdd pin and let see.
dediegokey
16th March, 2010, 06:54 PM
Hi Guys I bought X-prog and came with out software and power supply were I can dounwload sof and also
need Voltage and AMP values.
Thanks Luis
albertros
16th March, 2010, 09:34 PM
Hi,
the large chip is ATMEGA64.
DO NOT update firmware on a Chinese clone from the original site, it will shut down the firmware.
blackberry12
17th March, 2010, 08:05 AM
buy original
change usb cable
kasim_izmir
17th March, 2010, 08:49 AM
I've never use xprog-m but if its possible try to forward series a diode to the eeprom vdd pin and let see.
Hi, Ok i will replace all diods, i think 1N4148 or zener 5v1 :questionmark:
Zmann
17th March, 2010, 09:08 AM
Hi, Ok i will replace all diods, i think 1N4148 or zener 5v1 :questionmark:
No, it doesnt mean to replace all diodes. To put a diode or two in series to the Vdd (Vcc) pin is to lower the voltage supply to the chip. Your post showed that the programmer itself is not really faulty and it worked with MCU. I and some people experience with this, the Vdd is to close level to the other signals level when programming. Lower it for a few 0.x volts may help it working fine. Refer to the datasheet and if interest, read some post on Ponyprog forum. But im not sure you are the case, let try.
youssef70
17th March, 2010, 11:12 PM
Hi, Thanks for advice
I am not try to update never ...
I will buy xprog new one ..
BR
kasim
may be a good choice ... last clone do micronas ...
kasim_izmir
19th March, 2010, 02:50 PM
may be a good choice ... last clone do micronas ...
Yes, i buy new one xprog working good , full authorized ;)
BTW , do you have special pictures pdf etc. for user manuel
WBR
kasim
almlohe
21st March, 2010, 02:38 PM
hi
i baying xprog m but it s not work ineed help
thanks
florinyes
21st March, 2010, 04:32 PM
Yes, i buy new one xprog working good , full authorized ;)
BTW , do you have special pictures pdf etc. for user manuel
WBR
kasim
Is it really fully authorized? Does anyone got it allready and can confirm it works on secured motorola?
Cheers
morito
21st March, 2010, 07:08 PM
yes , works whit motorola secure
regards
ivanxxx
5th June, 2010, 11:36 PM
What did you do, to make it work with mcu-s, I have xprog and he reads eeproms but not mcu-s? Its new but cant read any hc05 hc11...
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.