MPPS

[lolooo1981]

to me no work, have same error of setupapi.dell
in xp instead have problem of loading driver
have try with 2 mpps

any solutions?

Do you use on same laptop after desinstall 3.38 version?

[noriginal]

Do you use on same laptop after desinstall 3.38 version?


yes
i can't use?

[zecas]

after using patch in vista sp2 my interface is not reconized anymore, is there any solution to have it working on vista? on xp with old laptop works fine.

thanks

[lolooo1981]

yes
i can't use?

I was problem with version 5 cracked version in winxp.
After remove v5 crackedsoft and reinstall v5 official, i don't be able to return to v5 cracked because i think this soft was problem with remove shield.I need to re-install winxp with sp3.And after, all run fine.I think you have same problem.

Best regards

[cosmind]

you must use old drivers

[lolooo1981]

you must use old drivers

Personnaly i using old drivers do not work because i already test this solution.Remove manualy registry entries, use old drivers etc...
Personnaly i use many solutions and no success...i had no choice to retry i zero point...but if someone have another solution,help would be appreciated for members in DK.

Run in official version with serial not blacklisted is the best solution i think (in stable versions for sure).

For other way, i use another V5 cracked version who work fine but seem a little different in drivers but protected by keygen and seems to work better in serial 236.

Best regards

[ka_rai]

hi friends

who have tested this version 8 , no crash cars same as version 5 ?
what you think about version 8 more stable ?

thank you ;)

[Shaheenem]

I was problem with version 5 cracked version in winxp.
After remove v5 crackedsoft and reinstall v5 official, i don't be able to return to v5 cracked because i think this soft was problem with remove shield.I need to re-install winxp with sp3.And after, all run fine.I think you have same problem.

Best regards

Same problem. I need to format PC and re-install win XP

[Dobermann]

Hello friends

i have MPPS original and clone !!

did someone know if the MPPS software 9.003 works on win2000 ??

ich cant get it to work !! sw version 8.2.10 works i make software update to version 9 and try to make firmware update to V9.02 !! on win2000 error unable to open device !!

with clone and original !!!

i tryed on my win xp prof works !! sw version 9.0.0.3 hw 9.02

interface is flashed to hw 9.02 but on win2000 it will not work !!

is there no support since version 9 for win2000 ??

thanks for answer and info !!

king regards !!

[Dakta]

Quick question - If you plug in MPPS clone (serial ends in 234) 3.0.2.37 into internet connected computer, does it block automatically?

[lolooo1981]

Quick question - If you plug in MPPS clone (serial ends in 234) 3.0.2.37 into internet connected computer, does it block automatically?

Mpps software is not connected to internet, no problem, but if you really want to block it, run it simply to 3.38 version :D

Best regards

[Dakta]

Haha cheers for that.

Got a mpps box - using the supplied software - 3.0.2.37 but it wouldn't connect to one of my vehicles so I wondered if it had 'automatically' updated itself over the internet (I didn't manually attempt to update it, but wondered if being connected to internet permitted an automatic download).

I shall assume then that it's the vehicles fault and try it again ;)

[mishu_b]

Haha cheers for that.

Got a mpps box - using the supplied software - 3.0.2.37 but it wouldn't connect to one of my vehicles so I wondered if it had 'automatically' updated itself over the internet (I didn't manually attempt to update it, but wondered if being connected to internet permitted an automatic download).

I shall assume then that it's the vehicles fault and try it again ;)


No automatically update posible up to now.
what case has your tool?

atb

[Dakta]

It's the silver box. It hasn't been used before so all I can assume is it's dead on arrival (DOA).

No attempt has been made to update it, though it has been plugged into computers that have internet access.

[lolooo1981]

Chineese clone...mine not work in arrival too...Serial 234?
If yes try to update with cracked version of Scary maybe help you.And ever...use it at your own risk...

Best regards

[Dakta]

Serial 234?

That's the one :)

I think i'll just buy a later unit. These sound way too problematic.

[rsibiza]

That's the one :)

I think i'll just buy a later unit. These sound way too problematic.


I believe you will encounter 100% same problems,with newer china clone.

The only good working mpps clones come from europe,they work with genuine sw,dont need any crack,loader which allows unit to work even with FFFFFF or 000000 serial...

If u want start business,buy good euro clone or original unit,but lot customer with original ones ran away from...who know why ...hehe

[bazare]

not really ... most of the Amt customers sold the v8 and v9 genuine tools and are working with clone v5 which is a lot better.

[Dakta]

not really ... most of the Amt customers sold the v8 and v9 genuine tools and are working with clone v5 which is a lot better.

Ironic, isn't it really!

But yeah I've heard of no-end of problems with the genuine tool when updated...what a put off. They're not exactly bust-your-balls expensive are they.

[riddler]

info my mpps obd lead v5.08 3.0.3.38 read/write bmw e46 320d edc16c31. and 118d edc16c35 with no problems

[VTL511]

i updated my mpps to V9 from V8 and now i cant add the drivers it only adds the interface as a human interface device

and i cant update the firmware since device is not found. i tried on WinXP and XP Pro

[lulu2003]

info my mpps obd lead v5.08 3.0.3.38 read/write bmw e46 320d edc16c31. and 118d edc16c35 with no problems

auto checksum working fine?
did you put 14v on the car as mentioned?

[blistograd]

Hello everyone.
There is a problem.
fiat doblo 1.3 jnd with ECU magnetti marelli MJD6F.D6
MPPS 5.0.1.10 on a line not yet read.
identifikatory not read, too.
CAN identifiers to read, but read the flash button is not active.
He opened the box and read BDM100. (Chinese clone)
tab, single, and after the export has size 518 KB flash and eprom 4 kb.
As I understand it's not a full size flash
how to read the full size flash and what size should be?
magnetti marelli
51862582
MJD6F3.D6\HW04P\3645-D670
SDE85HPEU4UEG0
8183YF2K
D032
MJDF3.DGBC010
1853A
AB15

[riddler]

checksum working fine, voltage 1210 no problems

[grinovsky]

the flash is in processore
the size shuld be less than 500Ko

[kana2000]

Hi
Is anybody have a MPPS version 5 working with clones?

[grinovsky]

yes,there is a cracked V5 for MPPS here
work fine with china clone
http://i43.servimg.com/u/f43/16/03/79/30/mpps11.jpg

[mishu_b]

...
you can find here on the forum section a lot of hints for this MPPS clone tool.

just spend few hours for this job, and you will find the solution.

atb

[riddler]

yes checksum working with no problems

[lolooo1981]

Like other members use version of scarymistake is the best solution for cracked V5 version.
But if you want more stability for V5 or other versions buy or reprogram MCU for officials versions.
Clone work fine as original.

Best regards

[mecadriano]

friends need to read and write, EDC16C9 ecu, need some opinion, I can do with the MPPS service to all,
Thank you.

[lolooo1981]

friends need to read and write, EDC16C9 ecu, need some opinion, I can do with the MPPS service to all,
Thank you.

Read/write alfa romeo Brera edc16C9 and opel Astra with no problem.After in what car what do you want to work ?

[mishu_b]

friends need to read and write, EDC16C9 ecu, need some opinion, I can do with the MPPS service to all,
Thank you.


if your tool is working on CAN - yes you can do for all.

atb

[lolooo1981]

For this ecu Can or kline that depend in what car do you want to work.

Best regards

[typergaz]

i have a mpps clone was running on version 1.0.8 or something like that and i got hold of a updated processor for around ?50 off ebay, poped it in and now im running v5.0.1.13 all fully working with new cars added and it looks and works loads better plus it now reads and writes can protocol as-well as it did not before this update

[FastGas]

mpps V9 is out!

[lolooo1981]

New software mpps V9.0.0.4 hw 9.02....nothing

Best regards

[ecutuners]

v9.0.0.4 still have problems, edc16u1 fails to read always "checksum block read error" , edc16u31 same problem, and edc16c9 opel write fail always at 91%

[bazare]

=)) they should stop trying :)) or just offer a solution to downgrade all interfaces to v5. I have same problem with edc16u1

[ecutuners]

i agree, the tool cant live for much longer, its dead

[RCS]

so what is the best clone interface to get and where?

get old 3.0.2.37 and get upgrade kit for it or just get v5 that works ot maybe go with v8 I have seen on ebay, some euro clone...

either way if you have any suggestions let me know here or just PM...

[pablo1971]

get it updated to v5 mate,and leave it there,its the most stable,with no glitches...

[faiscamix]

I never tried to update mine and it still works stable until today. Have one year of using without problem on any car that i've made with it. After reading some parts of all of this i got the conclusion (like we say here) is better to have ne bird at our hand than 2 flying. V5 is the stable one.

Best regards

[Dobermann]

hello

i have MPPS genuine and clone tool !!

i have running 9.0.0.4 and Hw 9.2

tryed many cars !! MPPS is not realy good working

they have many problems since they support win 64 bit systems !!


i sell my genuine tool !! i yesterday i tryed me7.5 i get no ID ecu not found !!

since V5 it is trash !!!!

edc16 not work edc15 not work

on weekend i will try opel astra siemens simtec

[lolooo1981]

Software 8.2.10 run normaly but V9..x have many problem i confirm it.

Best regards

[yellowstilo]

hello,
i just received my MPPS 8.0.2.10 clone from Belarus - after installation of the belonging software i plugged in the interface but in Device Manager it shows as a Human Interface Devices / HID Compliant Device / USB-HID

it shows these drivers were installed which i suspect to be the wrong ones:

C/Windows/System32/Drivers/hidclass.sys-hidparse.sys-hidusb.sys
C/Windows/System32/hid.dll

could someone with this version please check what drivers belong to this version and please post them here with their map location?
The program does not open - i guess that's because the interface is not recognised?
thanks a lot for your help, i hope i will get this interface up and running as it was too expensive to put it in the drawer with the other non-working tools....

[lolooo1981]

hello,
i just received my MPPS 8.0.2.10 clone from Belarus - after installation of the belonging software i plugged in the interface but in Device Manager it shows as a Human Interface Devices / HID Compliant Device / USB-HID

it shows these drivers were installed which i suspect to be the wrong ones:

C/Windows/System32/Drivers/hidclass.sys-hidparse.sys-hidusb.sys
C/Windows/System32/hid.dll

could someone with this version please check what drivers belong to this version and please post them here with their map location?
The program does not open - i guess that's because the interface is not recognised?
thanks a lot for your help, i hope i will get this interface up and running as it was too expensive to put it in the drawer with the other non-working tools....

Do you have version 5.0.1.10
installed before ?

[yellowstilo]

No , i deinstalled 5.0.113 before - should i reinstall this version and then upgrade the software?
The interface should have the 8.0.2.10 / 8.06 firmware installed when delivered?

[scarymistake]

hello,
i just received my MPPS 8.0.2.10 clone from Belarus - after installation of the belonging software i plugged in the interface but in Device Manager it shows as a Human Interface Devices / HID Compliant Device / USB-HID

it shows these drivers were installed which i suspect to be the wrong ones:

C/Windows/System32/Drivers/hidclass.sys-hidparse.sys-hidusb.sys
C/Windows/System32/hid.dll

could someone with this version please check what drivers belong to this version and please post them here with their map location?
The program does not open - i guess that's because the interface is not recognised?
thanks a lot for your help, i hope i will get this interface up and running as it was too expensive to put it in the drawer with the other non-working tools....
I'll get the same today at the post office and let you now how it go

[lolooo1981]

I think you must stay in version 8.2.10, the other update are not very stable.

Best regards

[scarymistake]

hello,
i just received my MPPS 8.0.2.10 clone from Belarus - after installation of the belonging software i plugged in the interface but in Device Manager it shows as a Human Interface Devices / HID Compliant Device / USB-HID

it shows these drivers were installed which i suspect to be the wrong ones:

C/Windows/System32/Drivers/hidclass.sys-hidparse.sys-hidusb.sys
C/Windows/System32/hid.dll

could someone with this version please check what drivers belong to this version and please post them here with their map location?
The program does not open - i guess that's because the interface is not recognised?
thanks a lot for your help, i hope i will get this interface up and running as it was too expensive to put it in the drawer with the other non-working tools....
My MPPS is working
deinstal mpps old versions
go to
regedit and look to
mpps
amt cartech
Multi Protocol Programming System
and delete the key's and ssub key's
install mpps v8
put in usb and conect to car and start mpps
:coffee:

[yellowstilo]

i did deinstall the previous version but on the AMT site it says you have to have version v5.x installed before you can install v8?
I also deleted all previous MPPS keys before installation of 8.0.2.10 but somehow the interface is not recognised - could you please check in device manager which drivers are installed with your interface?
I guess i need some dedicated AMT drivers like in version 5 and not some universal Windows drivers as mentioned above?
Thank you for your help !

[scarymistake]

i did deinstall the previous version but on the AMT site it says you have to have version v5.x installed before you can install v8?
I also deleted all previous MPPS keys before installation of 8.0.2.10 but somehow the interface is not recognised - could you please check in device manager which drivers are installed with your interface?
I guess i need some dedicated AMT drivers like in version 5 and not some universal Windows drivers as mentioned above?
Thank you for your help !
You dont need to install v5
deinstal mpps old versions
go to
regedit and look to
mpps
amt cartech
Multi Protocol Programming System
and delete the key's and ssub key's
install mpps v8 from amt-cartech
put in usb and conect to car and start mpps
so it workt for me
when i put in the usb i get in device manager two drivers
human interface
hid-compliant app
usb-hid
My os is Win xp sp3
:celticscarf:

[yellowstilo]

thanks for your reply Scary,
i see your drivers are the same as mine, you have one more in your file : hidserv.dll
I will try again but i guess i already tried all options, i will post my results !
thank you!

[scarymistake]

thanks for your reply Scary,
i see your drivers are the same as mine, you have one more in your file : hidserv.dll
I will try again but i guess i already tried all options, i will post my results !
thank you!By the way.
Have you contacted the seller

[gzk]

For people who have trouble because windows don't find drivers on v8 mcu

* first install 3.0.2.37
* after plug your v8 cable
* when it ask for drivers point \windows\system32\drivers\
it will detect it as flasher
* after that install v8 soft
* then launch in mpps folder upgrade
* it will upgrade the cable
* after that launch update
for me it tell me my cable is up to date so nothing to do more
* after that the computer will reconnect the cable as HID without ask you nothing

* after that you can desinstall v3 and launch mpps v8
enjoy

solution tested with viaken alu box v3 to v8 conversion by change mcu self soldered on XP Sp3 and WIN7 32Bits

[yellowstilo]

yes, i am waiting for his reply...
In the worst case scenario i will downgrade the interface to v. 5.0.1.13 but that's just as good as the alu clone which i upgraded to this version....

[yellowstilo]

well, i tried again, deinstalled all MPPS programs and all registery keys - reinstalled 8.0.1.20, plugged interface which shows the same drivers you mentioned -

still no joy, the program does not open....
I hope the seller comes up with a solution otherwise i will end up downgrading the damn thing.....
i'd better stay with my simple but working upgraded alu clone...

[lolooo1981]

well, i tried again, deinstalled all MPPS programs and all registery keys - reinstalled 8.0.1.20, plugged interface which shows the same drivers you mentioned -

still no joy, the program does not open....
I hope the seller comes up with a solution otherwise i will end up downgrading the damn thing.....
i'd better stay with my simple but working upgraded alu clone...

Sorry but i think you have no solution,return to point zero.
Reinstall winxp and service pack 3.
And install after mpps version you want.
I had this problem before and i not solve it.

For me its after desinstall 5.0.1.10 version.

Best regards

[yellowstilo]

Sorry but i think you have no solution,return to point zero.
Reinstall winxp and service pack 3.
And install after mpps version you want.
I had this problem before and i not solve it.

For me its after desinstall 5.0.1.10 version.

Best regards

that doesn't sound very encouraging - i have a lot of software installed on this laptop and will have lots of trouble reinstalling them...
I'm happy i have back-up laptops with MPPS 5.0.1.13 running.....
Would it be possible to reinstall 5.0.1.13 on this laptop and use it with my upgraded alu MPPS or is there a hidden file left which kills my 5.0.1.13 interface?

[gzk]

that doesn't sound very encouraging - i have a lot of software installed on this laptop and will have lots of trouble reinstalling them...
I'm happy i have back-up laptops with MPPS 5.0.1.13 running.....
Would it be possible to reinstall 5.0.1.13 on this laptop and use it with my upgraded alu MPPS or is there a hidden file left which kills my 5.0.1.13 interface?

Have you try my solution ?

[mishu_b]

...
the problem with this sw is following:

you need to have only one version installed in your computer - but you can run all other MPPS ver sw which you would like.

ex.
- install ver 5.0.1.10
- copy the entire folder where would you like.
- install ver 4.0.1.9
- go to Ver 5.01.10 folder and run the sw from there, you will see it is working.

- now it is up to you which version is installed into your PC and which are you running.

atb

[yellowstilo]

Have you try my solution ?

Hello, no, i did not reinstall the old 3.0 version because your solution was for a interface which could not find the correct drivers, my interface apparently finds the correct driver (as shown in the device manager) and does not ask for any driver, it even doesn't accept the old driver...
I guess i have a corrupted mcu, i will wait for the seller's answer but i'm afraid downgrading the MCU to 5.0.1.13 is the only solution without reinstalling my operating system...

[lolooo1981]

that doesn't sound very encouraging - i have a lot of software installed on this laptop and will have lots of trouble reinstalling them...
I'm happy i have back-up laptops with MPPS 5.0.1.13 running.....
Would it be possible to reinstall 5.0.1.13 on this laptop and use it with my upgraded alu MPPS or is there a hidden file left which kills my 5.0.1.13 interface?

I found only this solution after try many other.My laptop (a netbook) it's dedicated to car file transfert only.It's better easy for me.
Try Mishu solution, i don't try it.
After you are my solution...

Best regards

[lolooo1981]

that doesn't sound very encouraging - i have a lot of software installed on this laptop and will have lots of trouble reinstalling them...
I'm happy i have back-up laptops with MPPS 5.0.1.13 running.....
Would it be possible to reinstall 5.0.1.13 on this laptop and use it with my upgraded alu MPPS or is there a hidden file left which kills my 5.0.1.13 interface?

You are not be able to return on 5.0.1.13
Only in later version if your serial is not blacklisted.
Run in 5.0.1.13 simply not work.

Best regards

[yellowstilo]

You are not be able to return on 5.0.1.13
Only in later version if your serial is not blacklisted.
Run in 5.0.1.13 simply not work.

Best regards

I'm not sure you understood my question right - i just reinstalled the 5.0.1.13 software which still works fine with my old alu MPPS 3.0 which was updated with a v5 mcu -
I just can't get the new V8 interface up and running (deleted v8 software again), i'm considering now to put a 5.0 mcu inside to be sure it works just like the alu clone because i expect the 8.0 chip is corrupted...

[lolooo1981]

I'm not sure you understood my question right - i just reinstalled the 5.0.1.13 software which still works fine with my old alu MPPS 3.0 which was updated with a v5 mcu -
I just can't get the new V8 interface up and running (deleted v8 software again), i'm considering now to put a 5.0 mcu inside to be sure it works just like the alu clone because i expect the 8.0 chip is corrupted...

ok, sorry.
i think you must try your interface on another laptop before.
V8.2.10 run fine and have better compatibility with win vista and 7.But for the moment V9 is a big bulls**t.

Best regards

[yellowstilo]

ok, sorry.
i think you must try your interface on another laptop before.
V8.2.10 run fine and have better compatibility with win vista and 7.But for the moment V9 is a big bulls**t.

Best regards

i'm running Windows XP sp3 so i wonder if v8 has a lot of advantages vs. v5 for me.....
I tried to install v8 on another laptop , the drivers for the MPPS interface are installed automatically (verified with the drivers posted by Scary) but the program still won't open.
If the seller has no solution for this problem i will try if downgrading it with a v5 mcu will get this interface running...

[mishu_b]

...
as far as I know - the V8 version starts only if the tool is plug into USB port, maybe I wrong.
Have you tried in this way?

atb

[ecutuners]

Your problem is the sw from amtcartech, you need the first 8.0.2.10 to install, if you can't find I have it
Danny

[yellowstilo]

...
as far as I know - the V8 version starts only if the tool is plug into USB port, maybe I wrong.
Have you tried in this way?

atb

yes, i tried with the tool plugged in, don't work....

[yellowstilo]

Your problem is the sw from amtcartech, you need the first 8.0.2.10 to install, if you can't find I have it
Danny

i have installed the original 8.0.2.10 software from AMT...

[yellowstilo]

Well, the seller has advised me to install 9.0.0.3 to test if the soft/hardware works with that version -
At start-up the update popup appeared, i updated the interface successfully and could open the program after that.
It looked good but unfortunately the MPPS did not connect to my ecu (where a simple updated alu clone 5.0.1.13 works without any problems...)
This seems to be a problem of V9, now i'm stuck with a shitty, non-working version....
right now i'm negociating with the seller about a v5 chip, i hope this will finally get this interface running (although i did not buy this version to pay extra money to downgrade it because it doesn't work...)
to becontinued...

[scarymistake]

Well, the seller has advised me to install 9.0.0.3 to test if the soft/hardware works with that version -
At start-up the update popup appeared, i updated the interface successfully and could open the program after that.
It looked good but unfortunately the MPPS did not connect to my ecu (where a simple updated alu clone 5.0.1.13 works without any problems...)
This seems to be a problem of V9, now i'm stuck with a shitty, non-working version....
right now i'm negociating with the seller about a v5 chip, i hope this will finally get this interface running (although i did not buy this version to pay extra money to downgrade it because it doesn't work...)
to becontinued...
AMT-Cartech said to have an update to version 10
But i can not download it now but he is comming soon i thing.
Maybe you can try it if it can be downloaded

[lolooo1981]

AMT-Cartech said to have an update to version 10
But i can not download it now but he is comming soon i thing.
Maybe you can try it if it can be downloaded

Try with updater inside folder mpps software ?

[lolooo1981]

I verify in AmtCartech forum...
Update 10.0.1.0 will be available soon.
It seems to work better than 9.xx beta version

Best regards

[yellowstilo]

I verify in AmtCartech forum...
Update 10.0.1.0 will be available soon.
It seems to work better than 9.xx beta version

Best regards

If this new version 10.x is released on a short term i will try if this version solves the "ecu not found" problem - a 5.0.1.10 chip is ordered and shipped so if this fails too i will downgrade to v5...

[Dakta]

Just out of interest is there anything wrong with v5?

or is it just a lack of vehicle support? If it's stable for the cars in it's list then it looks like a half decent peice of kit.

[yellowstilo]

reading all posts i think V5 is the best version with the least problems - i guess AMT just released the later updates to attempt to reduce the MPPS clone business.....
The car list was not changed (or very little) - just a useless CPU usage indicator was added.
When v10 is posted i will give it a try but i'm not very confident after reading all comments on v8 and v9...

[lolooo1981]

reading all posts i think V5 is the best version with the least problems - i guess AMT just released the later updates to attempt to reduce the MPPS clone business.....
The car list was not changed (or very little) - just a useless CPU usage indicator was added.
When v10 is posted i will give it a try but i'm not very confident after reading all comments on v8 and v9...

V8.0.2.10 work good also with more speed in CAN.Stable as i know.V9 Big sh** !
V10 seems to not have new protocol...What next ?...If this continu in this way,this tool will be dead.
Seems the time is come to buy other tool.
Maybe new powergate or other...

Best regards

[eddieddi]

In V10 software VAG EDC15 is working again, i have tested today. In the last few versions it did not....
I hope that AMT have finished the experimets with the V8-9 USB-HID Driver and now will work on new protocols and cars.
we will see....

[bazare]

The big question is ... any new cars added in v10? Because edc15 was working very well also in v3 v4 v5 :shot:

[scarymistake]

In V10 software VAG EDC15 is working again, i have tested today. In the last few versions it did not....
I hope that AMT have finished the experimets with the V8-9 USB-HID Driver and now will work on new protocols and cars.
we will see....
Can you upload version 10 please
so we can try it

[scarymistake]

V10 from amt-cartech

Beta Downloads (http://www.amtcartech.com/version10.html) not for clone

You may have to install the drivers manually for this version.

And its working now

[lolooo1981]

who test this version ?
The problems are gone ?

[yellowstilo]

i just tested it , had to reinstall the drivers manually and to update the firmware -unfortunately it still shows 100% cpu usage / ecu not found...
Could it be possible my (rather old ) Dell D610 is too slow for these newer versions?
I run Windows XP /sp3 , 1,73 gHz / 2mb cache memory, 1 gb memory.
I connected a multimeter to the K-line and see a few voltage drops when i press ecu data so i guess MPPS tries to connect to the ecu...
Unfortunately i don't have a newer/faster laptop to test this version, i will wait for other comments...

[exxl]

on what ecu you are trying to read out the id ?

if it is on k-line it could be that lm339 or hc32d is defect,
if it is on can then check sja1000t and the smd 8 pin driver 2551.

btw. i just tested my mpps with 10.0.2.3 version on vag edc16u34 and it works very well read and write, will tonight try on my other car audi a4 with edc15, will let you know about it.

regards

[yellowstilo]

i try to read a IAW5NFT1 ecu from a Fiat Stilo (K-line) - worked without problems with a alu clone with v5 upgrade chip.
I will try to replace the two chips, will post the outcome here.....
thanks for your help !

[mishu_b]

...
have your tool worked out before update?

atb

[yellowstilo]

...
have your tool worked out before update?

atb

Hello, no it never worked from the start - i bought it as non-China v8 , upgraded to v9 on request of the seller, now upgraded to v10 but it just don't connect to the ecu while a cheapo v5 clone works without any problem...
It does show all tool and software/firmware data so i guess the mcu is programmed o.k. (confirmed by updater)
I will replace the two mentioned chips and hope this will solve my problem.
I also just ordered a second alu clone v5 as back-up, it's just 36.50 euro including free shipping from China at the moment....
If i can repair the v10 tool i will use my ordered v5 chip to update this clone as i expect it will be a v3 with the v5 patch...
to be continued....

[zlatinou]

the same problem for me.
i have a european v8 clone and works with no problems with the v8 software.
but with the v9 my mpps doesn't work with my golf5 edc16u1
and it's the same with the v10!!!! he doesn't work.

[ipejasinovic]

From which side of Europe is your device?

[yellowstilo]

From which side of Europe is your device?

Mine is from Belarus....

[lolooo1981]

Someone test on edc16C9 ?

[scarymistake]

who test this version ?
The problems are gone ?
Mine is also from Belarus purchased as a v8
i test it with v8 reading and writing ok edc15 and edc16 psa:shot:
v9 no reading and writing edc15 and edc16 psa:mad:
v10 reading and writing edc15 ok :coffee:
Tomorrow I try EDC16 and i let you now

look here more info
http://forum.amtcartech.com/index.php?topic=3.0;prev_next=prev#new

[elchip]

V9 have problem K-line but CAN work.
V10 in testing from me too.
Will raport
Regard's

[zlatinou]

From which side of Europe is your device?

mine is from uk

[Dobermann]

hello i use now V 10.0.2.3

for me nothing works !!

i tryed to read ME7.5 audi s3 and seat leon

no communication !! no id no read nothing !! :hmmmm::hmmmm::hmmmm:

thats really sad !!

my hope was that the problems are gone with the new version !!

but that was dream

now K line will not work !! i try can TFSI Golf tommorow !!

[zlatinou]

hello i use now V 10.0.2.3

for me nothing works !!

i tryed to read ME7.5 audi s3 and seat leon

no communication !! no id no read nothing !! :hmmmm::hmmmm::hmmmm:

thats really sad !!

my hope was that the problems are gone with the new version !!

but that was dream

now K line will not work !! i try can TFSI Golf tommorow !!
for me just id work but read doesn't work on golf5 edc16 u1 kline.
work with v8 but doesn't work with v9 and v10

[Dobermann]

for me just id work but read doesn't work on golf5 edc16 u1 kline.
work with v8 but doesn't work with v9 and v10


i think V10 is the same trash like V9 !!

but with V9 i could read me7.5 with a little trick

i make ID with me7.1 than i switsh to me7.5 and click read !!

that was working on me7.5 with V9 now with V10 nothing !!

i dont know what they are doing in the Factory but its trash too for the moment !!

nothing works right !! i think the drivers are the problem !!

what windows do you use ??? i use win xp prof 32 bit on win2000 MPPS is not working !!!

[soundnavigator]

If you have original tool, send log file to AMT to resolve the problem in next update ... maybe.

Best regards.

[mishu_b]

Hello, no it never worked from the start - i bought it as non-China v8 , upgraded to v9 on request of the seller, now upgraded to v10 but it just don't connect to the ecu while a cheapo v5 clone works without any problem...
It does show all tool and software/firmware data so i guess the mcu is programmed o.k. (confirmed by updater)
I will replace the two mentioned chips and hope this will solve my problem.
I also just ordered a second alu clone v5 as back-up, it's just 36.50 euro including free shipping from China at the moment....
If i can repair the v10 tool i will use my ordered v5 chip to update this clone as i expect it will be a v3 with the v5 patch...
to be continued....

Q: when you try to "ECU ID" - do you get the message "ECU not found"? - (for K line)

if yes - change the LM339 and HC device - maybe it will work!!!!


Q: for CAN - what message do you receive for "ECU ID"?

atb

[yellowstilo]

Q: when you try to "ECU ID" - do you get the message "ECU not found"? - (for K line)

if yes - change the LM339 and HC device - maybe it will work!!!!


Q: for CAN - what message do you receive for "ECU ID"?

atb

yes, i get message "ecu not found" upon "ecu id" request on K-line with version 8,9 and 10 - i will replace both chips as suggested and post te results.
Same test with simple alu clone with v5 update chip works o.k....

I did not test it on CAN because i only use the MPPS for my private car (Stilo 1.6 with K-line for diagnostics and reprogramming)

thanks for your help...

[scarymistake]

If you need it the drivers from v10

[exxl]

can confirm now that vag edc15 is working too, did not write it but id and read goes smoothly so i think the writing would go too.

for me v10 works good till now

[scarymistake]

Mine is also from Belarus purchased as a v8
i test it with v8 reading and writing ok edc15 and edc16 psa:shot:
v9 no reading and writing edc15 and edc16 psa:mad:
v10 reading and writing edc15 ok :coffee:
Tomorrow I try EDC16 and i let you now

look here more info
MPPS Version 10 available from the AMTcartech website for downloading (http://forum.amtcartech.com/index.php?topic=3.0;prev_next=prev#new)
edc16 psa working reading and writing car is runing
edc15 psa working reading and writing car is runing
me744 psa not working but also not working on v5 and v8

[lolooo1981]

anyone test on opel edc16C9 ?

[e.t.]

Test anyone 7.6.2 opel? V5?

[zlatinou]

Test anyone 7.6.2 opel? V5?

i have read bmw 5series 525d e60 year 2006 edc16c31 with no problem with the version 10

[elchip]

MB EDC16C4 work perfect on K and CAN V10.

Regard's

[miggi]

Q: when you try to "ECU ID" - do you get the message "ECU not found"? - (for K line)

if yes - change the LM339 and HC device - maybe it will work!!!!


Q: for CAN - what message do you receive for "ECU ID"?

atb

Can you explain this, i cant follow you?
LM339, HC Device..??

i have also "ECU not found" with Me7..
i use v10, orig. tool
many thanks

[Dobermann]

Can you explain this, i cant follow you?
LM339, HC Device..??

i have also "ECU not found" with Me7..
i use v10, orig. tool
many thanks


hello do you use original mpps tool ??? i too !!

i tryed me7.5 but always ecu not found or no information

id - read/write >>> will not work

with V9 it was possible to read/write with the my little trick

but now nothing works on me 7


what car did you try ???

[soundnavigator]

People, write for all this problems in AMT forum and maybe upload the log files.

Best regards.

[yellowstilo]

Can you explain this, i cant follow you?
LM339, HC Device..??

i have also "ECU not found" with Me7..
i use v10, orig. tool
many thanks

LM339D and 74HC32D are two smd chips inside your MPPS - you can replace them by desoldering and resoldering .....
I'm still searching for a supplier who sells small quantities.

[miggi]

@Dobermann
i tried Audi S3 Me7.5 (29f400)


with byteshooter, galetto etc. no problems...

[Dobermann]

@Dobermann
i tried Audi S3 Me7.5 (29f400)


with byteshooter, galetto etc. no problems...


hello i tryed my seat leon cupra R 1.8T Me7.5 (29F800BB)

and Audi S3 1.8T

with V10 nothing works always no information or ecu not found !!

with V8 and V9 i could read/write

i have the Optican one it works great !!

i will sell my MPPS tool !! im angry !!

V8 V9 V10 in 3 or 4 weeks !! they have big problems !! i think the driver are trash

i dont know but my patience with this tool is at end !!

simply ME7 no communication what should i say :hmmmm::hmmmm::hmmmm::hmmmm:

[miggi]

i dont understand why they dont go back to the old drivers if they are stable, "anti-cloning" does not work anyway...

[Dobermann]

i dont understand why they dont go back to the old drivers if they are stable, "anti-cloning" does not work anyway...


+1

yes right !!

[lolooo1981]

The future seems to be compromize for this tool.
I hope new buyer of this tool are prepared their a**.
For 1650 euros genuine tool and big problem in new version are in the party !
Maybe an evolution in few next week ?But for the moment i don't think so...

Best regards

[TribesMac]

Is checksum written correctly on EDC16C39 with MPPS v5?

(Fiat JTDm engine)

I know v3 had problems, anyone tried with v5?

[FastGas]

mpps v8.0.2.10 does not write EDC16C39 Fiat Mjet, Unknow error

Reading ok

solution?

[Mickass]

So what is the best version of clone?
The V5 or V8?

:hmmmm:

[ipejasinovic]

v10 :D

[TribesMac]

Is checksum written correctly on EDC16C39 with MPPS v5?

(Fiat JTDm engine)

I know v3 had problems, anyone tried with v5?

Tested today, Fiat JTDm EDC16C39 works fine with MPPS v5... no problems whatsoever...

[mishu_b]

LM339D and 74HC32D are two smd chips inside your MPPS - you can replace them by desoldering and resoldering .....
I'm still searching for a supplier who sells small quantities.


Farnell / Electronic Component Distributors / Suppliers / Electronics, Electrical Parts, Electrical Components and Wholesale Electronics. (http://www.farnell.com)

atb

[marujon]

i've tried to write saab 93 edc16c39 ecu (opel ecu) and reads ok but fails to write (ITS CAN). says : ecu not found when try to start writing... V5.0.1.10 clone too, not original.

[lolooo1981]

Who test V10 in Merelli 59M specialy on Ducat 999 superbike ?

[yellowstilo]

Farnell / Electronic Component Distributors / Suppliers / Electronics, Electrical Parts, Electrical Components and Wholesale Electronics. (http://www.farnell.com)

atb

i just spoke to them, for a private buyer minimum order is 50 euro, for companies there is no minimum order amount....
the chips cost almost nothing, i could buy a bag full for 50 euro but i only need 1 or 2 of each....
Are there any DK members with a company who would be willing to order a few of these chips for the MPPS for just a few euro's?

LM339D > nr. 2293778 > 0.21 euro/pc > +10 pc > 0.134 euro
74HC32D > nr. 1085329 > 0.33 euro/pc > +10 pc > 0.25 euro

if one of you would buy 10 of each (total 3,84 euro!!) i would like to buy a few or all of them, maybe there are other MPPS owners who would like to buy some spare chips too...
I hope someone can help me with this...
thanks !

[scarymistake]

V10
Reading and writing a saxo m744 ok

[Dobermann]

i just spoke to them, for a private buyer minimum order is 50 euro, for companies there is no minimum order amount....
the chips cost almost nothing, i could buy a bag full for 50 euro but i only need 1 or 2 of each....
Are there any DK members with a company who would be willing to order a few of these chips for the MPPS for just a few euro's?

LM339D > nr. 2293778 > 0.21 euro/pc > +10 pc > 0.134 euro
74HC32D > nr. 1085329 > 0.33 euro/pc > +10 pc > 0.25 euro

if one of you would buy 10 of each (total 3,84 euro!!) i would like to buy a few or all of them, maybe there are other MPPS owners who would like to buy some spare chips too...
I hope someone can help me with this...
thanks !


hello i have two of this smd chips (LM339D) here !!

if you need it send pm !!

[yellowstilo]

Hello Dobermann,
thanks for your offer , i sent you a PM but your mailbox is full and the message was rejected.
Would you please send me a PM with the price including shipping the chip(s) to the Netherlands?
When you have cleaned your mailbox i will reply in private.
I hope this will finally get my MPPS v8/9/10 working....
thanks !

[gzk]

V10
Reading and writing a saxo m744 ok

did you know if it was working with V8 ?
it's M 7.4.4 or ME 7.4.4 ?

[scarymistake]

did you know if it was working with V8 ?
it's M 7.4.4 or ME 7.4.4 ?
its a saxo 16cc 8v with a Bosch m744 l4 computer 0261206860 1037353564 and v8 i dont now :driver:

[soundnavigator]

V10
Reading and writing a saxo m744 ok


I test to read Peugeot 307 1.6 16V with ME 7.4.4 ... without success, only ID. No read, no log file, just processing. Is there a trick to read?

Best regards.

[scarymistake]

I test to read Peugeot 307 1.6 16V with ME 7.4.4 ... without success, only ID. No read, no log file, just processing. Is there a trick to read?

Best regards.
do you have a 7.4.4. or a 7.4.5 ??
try it to read with a saxo 744 or a 106 744

[soundnavigator]

The ECU is ME 7.4.4. I tried as Saxo 7.4.4, 106 7.4.4, 206 7.4.4 and in all the result is the same. When I receive ID and info message " ECU information complete " after that come message " Security access " and ... I can wait .. 5, 10, 15 min ... without result ... only green and yellow led fleshed.

Best regards.

[gzk]

its a saxo 16cc 8v with a Bosch m744 l4 computer 0261206860 1037353564 and v8 i dont now :driver:
thanks you i have one turbo and tired to desolder ship

[lolooo1981]

I have tested V10 on :
. Mercedes Sprinter edc16C31 Work OK
. Golf Edc16U1 1.9 Tdi Not work
. Opel Zafira Edc16C9 Not work
. Seat ibiza 1.9 Tdi edc15P+ Work ok
. Seat Leon 2.0 Tdi Siemens PPD Work ok
. Opel Vectra edc15M Work ok
. Bmw Edc16C35 Work ok
. Iveco 2.3 and 2.8 edc16C Work ok
. Peugeot Boxer edc16C39 Work ok
. Audi S3 Me 7.5 Work ok

Best regards

[miggi]

I have tested V10 on :
. Mercedes Sprinter edc16C31 Work OK
. Golf Edc16U1 1.9 Tdi Not work
. Opel Zafira Edc16C9 Not work
. Seat ibiza 1.9 Tdi edc15P+ Work ok
. Seat Leon 2.0 Tdi Siemens PPD Work ok
. Opel Vectra edc15M Work ok
. Bmw Edc16C35 Work ok
. Iveco 2.3 and 2.8 edc16C Work ok
. Peugeot Boxer edc16C39 Work ok
. Audi S3 Me 7.5 Work ok

Best regards

strange, all me7.5 i have tried i never had success...

[cosmind]

what time for read and write on Peugeot edc16c39 ?
v5 dont read this ecu

[scarymistake]

what time for read and write on Peugeot edc16c39 ?
v5 dont read this ecu
V10 approximately 10 minutes

[gzk]

strange, all me7.5 i have tried i never had success...
tested leon cupra R ME7.5 on V8 original soft + V8 clone MCU on viaken style alu box V3 clone : read write ok

edc 15 hyundai ok
edc15 vag ok
edc16 golf 6 ok

[Dobermann]

tested leon cupra R ME7.5 on V8 original soft + V8 clone MCU on viaken style alu box V3 clone : read write ok

edc 15 hyundai ok
edc15 vag ok
edc16 golf 6 ok

V8 worked better with me7 than V10 now

with V8 i could read/write me7.5

[lukaszek30]

http://www.euroeuro.pl/mpps.jpg
if it helped you press the button thanks

[ROBERTby2000]

tested leon cupra R ME7.5 on V8 original soft + V8 clone MCU on viaken style alu box V3 clone : read write ok

edc 15 hyundai ok
edc15 vag ok
edc16 golf 6 ok

golf 6 it`s not edc17?

[gzk]

golf 6 it`s not edc17?

GOLF 5 SORRY

[Mickass]

RENAULT LAGUNA 3 DCI 130hp 2008 EDC16CP33 not work with my MPPS V8 clone...
"ECU not Found" ?

[lolooo1981]

RENAULT LAGUNA 3 DCI 130hp 2008 EDC16CP33 not work with my MPPS V8 clone...
"ECU not Found" ?

Did you try in both kline/Can ?

[sherl645]

Hi,
I am trying to decide which MPPS to buy.

Does anyone know if V10 will read & write EDC16C39 in an 8 Valve Opel Zafira CDTi. I usually try to read these with BDM but someone has destroyed the pads on this one.

All the listings only say EDC16C39 16 Valve but as far as I know the ECU is very similar.

Version 10 is much more expensive than version 3 or 5 so I don't know where the benefits are.

Thanks,
Ronan

[bazare]

buy an european clone v5 with working CAN. You will be able to read all edc16 opel c9 / c39 with NO READ patch

[z786]

any news on the updates? have the mpps's started to work

[lolooo1981]

any news on the updates? have the mpps's started to work

No, Last update is 10.0.2.3
No news

Best regards

[gzk]

V10
Reading and writing a saxo m744 ok

V8 MCU ON CLONE
M7.4.4 OK BUT DATA ONLY 64KO NOT FULL FILE 512K R/W OK

[elchip]

V8 MCU ON CLONE
M7.4.4 OK BUT DATA ONLY 64KO NOT FULL FILE 512K R/W OK

Only clone which work with original SW and without any crack and loader's can be reference.

All other is nothing.

Regard's

[gzk]

my clone work on original mpps software downloaded by me on the amt cartech site

the hardware is a V3 clone from viaken who was warking in originial V3 software .

i have order an V8 mcu i have solder by myself in place of the V3 mcu .

i have download the soft from amt and voila

work without any crack or patch or modified version only original soft from amt

[obnchip]

Hi!
Exist patch or crack for v8?

[lolooo1981]

Hi!
Exist patch or crack for v8?

Not for this time, mate,sorry.
Perharps in 6 month.

Best regards

[majorahole]

So will this read/write/cheksum on a golf 5 med9?

[lolooo1981]

So will this read/write/cheksum on a golf 5 med9?

I read and write seat leon TFSI Med9 without any problem with V5 too,i think for this car you can.

Best regards

[majorahole]

Thanks, that's v5 only? Or will the older version work too? With checksums too?

[lolooo1981]

Thanks, that's v5 only? Or will the older version work too? With checksums too?

I don't try with V8 or V10,But with V5 and if this is Med9.1,yes,checksum is calculated by the program.Other med9.5 you need to calculate checksum.

Best regards

[lolooo1981]

try to resolv problem of edc16C9,someone have more info ?

[Mickass]

I read and write seat leon TFSI Med9 without any problem with V5 too,i think for this car you can.

Best regards

The version V5 is really stable....

[e.t.]

hi! Had anyone ever problems with EDC15 A2 1.4tdi?
I could not read it!
5.0.1.13 is the mpps software

[Amine13]

hi! Had anyone ever problems with EDC15 A2 1.4tdi?
I could not read it!
5.0.1.13 is the mpps software
Hello; are you sure it's EDC15 ?
Regards.

[lolooo1981]

hi! Had anyone ever problems with EDC15 A2 1.4tdi?
I could not read it!
5.0.1.13 is the mpps software

In many old car Vag group fuse remove is needed to access to ECU perhaps its the same way...

Best regards

[Mickass]

hi! Had anyone ever problems with EDC15 A2 1.4tdi?
I could not read it!
5.0.1.13 is the mpps software

Use the galletto 1260 for all EDC15....

[e.t.]

I remove the fuse but its not reading.

I take the galletto and it works fine

[grinovsky]

I remove the fuse but its not reading.

I take the galletto and it works fine
USE THIS OPTION
with MPPS you don't need to remove fuse for vag edc15
http://i43.servimg.com/u/f43/16/03/79/30/120.jpg

[e.t.]

Ok thanks, i will test it!

[gzk]

since i use mpps i never have to remove fuse or anything for vag edc15 and the recover work well .

[nicole99wu]

Interested to know me too, I remap a Fiat Grande Punto and I think it works only this cable loss.
If you know where I can buy it there would be really grateful!
you can buy this it works well. thanks...
:wink:

[eduardo74]

I have also problem on some 1.9TDI from 2000, 2002 with EDC15, on newer cant do Ecu Id with v5 clone

[gzk]

I have also problem on some 1.9TDI from 2000, 2002 with EDC15, on newer cant do Ecu Id with v5 clone


edc15 vag confirmed to work flawless on V3 V5 and V8 on clone with original or patched software.
if you get trouble perhaps your clone is bad

[gzk]

you can buy this mpps clone (http://www.chinasinoy.com/wholesale/smps-mpps-v50-tuning-remap-chiptuning-k-can-flasher-cable-1258.html), it works well. thanks...
:wink:

too expensive.
you can buy good V3 clone for 40usd and upgrade it yourself with patched V5

[yellowstilo]

hello i have two of this smd chips (LM339D) here !!

if you need it send pm !!

Hello Dobermann,

chips received today and finally got my MPPS V8/9/10 working !

thanks again for your help !!

[obnchip]

I have also problem on some 1.9TDI from 2000, 2002 with EDC15, on newer cant do Ecu Id with v5 clone

Mine is works v3 updated to v5...

[gtmech]

original tool cost 1000euros, so it is really worth it to by clone?:afraid:

where do i buy original?

[straki007]

I recommend buy MAGpro2. Now I got it and totally satisfied.
MAGPro2 tools (http://www.magic.com.pl/magpro2tools.html)

[noriginal]

too expensive.
you can buy good V3 clone for 40usd and upgrade it yourself with patched V5

a good clone of best quality less of 90$ don't exist
40$ is in your dream

[gzk]

a good clone of best quality less of 90$ don't exist
40$ is in your dream

how can you explain i have 2 clone working without issue on all the car i have report to test all over this thread ?

i have on from viaken and one from ebay china seller

they were both V3

i have no issue on the V3 on all the report to work car i have read.

now the viaken one is upgraded with a V8 mcu and the china is update in V5 with the scary mistake patched version .

still work ok .

the china clone cost me 40us on ebay and is on alu box like the viaken clone .

[obnchip]

Mine was 65usd.v3 updated to v5.working good with vag edc16!This seller is trastable got it in 10days...

Wholesale 2011 Newly V5.0.0.10 Ecu Chip Tuning MPPS (http://www.aliexpress.com/product-gs/405584336-2011-Newly-V5-0-0-10-Ecu-Chip-Tuning-MPPS-wholesalers.html)

[z786]

has v10 worked for any1?

[scarymistake]

has v10 worked for any1?
yes with a clone
W & R
Psa
EDC16c34 (c4)
EDC15 (c5)
ME744 (saxo 106 and 206)
:wink:

[lolooo1981]

has v10 worked for any1?

For me 2 chinese clone updated and they work on V10.

Regards

[psico]

any software to upgrade from v5 to v10? or just changing mcu possibility

[lolooo1981]

any software to upgrade from v5 to v10? or just changing mcu possibility

For the moment,only with new MCU or by reprogram with external programmer.

Best regards

[autochampion1]

V8 not work with EDC16CP31. Ident OK, read not connect (((

[kissato]

Hi all.

My S-mps is blocked with firmware update version 6.01

This happened when i updated the software for 5.0.1.10

Any ideas to recover my mpps? Thanks

[egyclick]

Hello dk friends, did someone succesfull read/write opel edc16c9 / c39 with clone mpps, if yes with what version?
I need to do it on a Zafira B year 2005 150hp with dpf

Thank you!

[grinovsky]

Hello dk friends, did someone succesfull read/write opel edc16c9 / c39 with clone mpps, if yes with what version?
I need to do it on a Zafira B year 2005 150hp with dpf

Thank you!
the mpps will read this ecu,but it will give you a partial read
in this partial read most of maps are not
for exemple,in this dump there is 4 maps for egr(full read)
but in mpps dump,you will find only one maps
so,it's impossible that you succes your tuning with mpps
you will get after tuning several cut in acceleration and a beautiful lampe on in dash with lim mode
the best way is to use bdm 100 to read this ecu

[macxlulu]

zafira cdti 150 goes off in reading the mpps fap tested it. it is safer to use the BDM

chiptuning cdti 150-only bdm
chiptuning cdti 120 -mpps or bdm

[egyclick]

Thank you dear grinovsky (http://www.digital-kaos.co.uk/forums/members/193009-grinovsky/) and macxlulu (http://www.digital-kaos.co.uk/forums/members/100332-macxlulu/) for the straight answers. I will try my luck with CMD1255 although I managed to screw a bmw ecu 3 years ago, hope this second time to do it ok.

Kind regards!

[bazare]

MPPS will work ok in that ECU for regular tuning... some of us previously tuned that car and aren't speaking from what we think. :)

[grinovsky]

Thank you dear grinovsky (http://www.digital-kaos.co.uk/forums/members/193009-grinovsky/) and macxlulu (http://www.digital-kaos.co.uk/forums/members/100332-macxlulu/) for the straight answers. I will try my luck with CMD1255 although I managed to screw a bmw ecu 3 years ago, hope this second time to do it ok.

Kind regards!
please egyclick (http://www.digital-kaos.co.uk/forums/members/90179-egyclick/) make me favor
read the dump by MPPS and by BDM100 and upload the 2 dump here for compare between the 2 reading:celtictop:

[egyclick]

please egyclick (http://www.digital-kaos.co.uk/forums/members/90179-egyclick/) make me favor
read the dump by MPPS and by BDM100 and upload the 2 dump here for compare between the 2 reading:celtictop:


Ok I will post them for you guys so you can decide who was right but what I don't understand is that EVC BDM100 leaves pins 3 & 4 empty and places the pins as shown on the photo attatched.
CMD BDM says to use first 10 pins instead as in photo attatched.

I have CMD1255 but the ECU must have same pinout no matter what tool I use.

[grinovsky]

MPPS will work ok in that ECU for regular tuning... some of us previously tuned that car and aren't speaking from what we think. :)
i have done zafira 1.9cdti and i know about what i speak
attached 2 dumps for the same ecu:ZAFIRA 1.9 cdti EDC16C39
HW:0281017064
SW:1037505798
in full read by BDM100 we find 6 maps for egr:
158E18-170EA8-176D68-180DE8-18DE7C-1C2F78
in partial read by MPPS we find only one maps:
1C2F78
in full read dump by BDM100 winols find 442 maps
in partial read dump by MPPS winols find only 165 maps
so,it's impossible to succes chiptuning this ecu with MPPS

I think when the proffessionnel speak the newbes must listen

[egyclick]

Ok I will post them for you guys so you can decide who was right but what I don't understand is that EVC BDM100 leaves pins 3 & 4 empty and places the pins as shown on the photo attatched.
CMD BDM says to use first 10 pins instead as in photo attatched.

I have CMD1255 but the ECU must have same pinout no matter what tool I use.

still can someone explain why the connections shown by CMD and EVC are different on same ECU ?

[tehnosoftex]

still can someone explain why the connections shown by CMD and EVC are different on same ECU ?
I can explain. The EVC bdm use vf0 and vf1 pins for reading writing on bdm port. CMD did not use these pins. If you read datasheet you will see that for accessing the mcu by BDM port you can use vf0 and vf1 or you cannot use but you must use another method:

"It is possible to determine whether the processor is halted in the debug state solely by looking at the Freeze status bit in the DSDO bitstream rather than using the VFLS[0:1] or FRZ pins. Most debuggers do not support this configuration."

also the evc has a led which will show if the ecu has power or not, the cmd did not use that function , that's why cmd did not use all pins which use evc

[bazare]

i have done zafira 1.9cdti and i know about what i speak
attached 2 dumps for the same ecu:ZAFIRA 1.9 cdti EDC16C39
HW:0281017064
SW:1037505798
in full read by BDM100 we find 6 maps for egr:
158E18-170EA8-176D68-180DE8-18DE7C-1C2F78
in partial read by MPPS we find only one maps:
1C2F78
in full read dump by BDM100 winols find 442 maps
in partial read dump by MPPS winols find only 165 maps
so,it's impossible to succes chiptuning this ecu with MPPS

I think when the proffessionnel speak the newbes must listen


:wink: Only one data block is active in that ECU ... and guess what ... it's the second one which is active:))
STOP DREAMING!!! But you probably have no idea where is the switch.

[grinovsky]

:roflmao:so erease the other bloc,it haven't utility

[bazare]

you tuned one zafira and I tuned probably one hundred Opel's with edc16c39 ... but you are the specialist indeed :)
Do you even know why data blocks are used and what for?

[macxlulu]

says it is like the bazare (http://www.digital-kaos.co.uk/forums/members/164387-bazare/), one cdti ecu has two maps to version 120 and 150 hp so when we throw the obd file always saves in August when encoding at 120 hp versions so you can do for the chiptuning obd version 120 by a 150-by BDM

[grinovsky]

fanatic:The term fanatic refers to some one who in the name of faith, is able to do anything to make it prevail

[macxlulu]

will come to your car to remove it fap shoot by obd regardless of whether or version 120 or 150 hp, and report, then see if you're right ...

ok?

[grinovsky]

it's looks like the engeneers who have make ecusafe2.0 don't know that the 1st bloc is desactived in opel edc16c39,becose ecusafe desactive the singles of DPF in the 1st bloc!!!
http://i43.servimg.com/u/f43/16/03/79/30/a10.jpg

[macxlulu]

Opel edc16c9
not edc16c39 must use bdm

[bazare]

this topic is about MPPS. The answer is YES - you can use MPPS to tune edc16c39 - Opel, partial read is enough.
Stop changing the subject.

[mombasa]

I agree for edc16c39 it is ok with mpps

[grinovsky]

this is an original BDM read for opel EDC16C9
it have 2 BLOCS too(may be one of them is desactived like say our engineer)
winols detect 564 maps
and it have 9 egr maps
8 egr maps in the 1st bloc
1 egr maps in the 2nd bloc
so,only for succes to programme the egr to keep it closed,your dump shuld have the 2 blocs that are in dump
so,conclusion,EDC16C9 and EDC16C39 must be read full to succes any tuning,if you say other think that's becose you have never done one Mr:B

[macxlulu]

opel astra edc16c9
fap remove
read by OBD
WRITE BY ODB

car work ok
:wink:

[macxlulu]

opel zafira edc16c39
fap remove

READ BY OBD MPPS
WRITE BY OBD MPPS

car work ok
:wink:





I understand the topic fap in Opels have closed :D

[grinovsky]

opel astra edc16c9
fap remove
read by OBD
WRITE BY ODB

car work ok
:wink:
and you think that is a proffessionel job?
what do you mean by work ok? it started?and move on road?
do you think,that if it was DPF OFF was done by BDM,the result will be the same than your DPF OFF by OBD
the most important,is when you flash flash the ecu with partial read you will lost synchronisation between cheksum blocs in the ecu,this is what you have do
attached the prove
see synchronisation between cheksum bloc in BDM read fille,it's green color
http://i43.servimg.com/u/f43/16/03/79/30/bdm_re10.jpg

[grinovsky]

and this is what you have do,so,it's impossible that this car will run perfect becose his ecu is ill,and need to be repaired by a pro,and this will happen,soon or later
http://i43.servimg.com/u/f43/16/03/79/30/mpps_r10.jpg

[macxlulu]

friend, when you will be use obd flasher :) you see mpps chcecksum calc in writing :D

ps.
I have too many cars teeth with every play with the BDM, if such opportunity is the obd I do :D

ps.2 ALL CAR WORK OK
BDM FILE :wink:

[grinovsky]

yes,the cks is calculated in writing,that's way the car start,but you will lost the synchro of cks between the blocs in the chip
learn more about this,
and for your information,the most difficult ecu that i had chiptuning,have more than 1400maps,and i did it with succes:D

[macxlulu]

I am very happy about it:) respects ambitious People

[bazare]

yes,the cks is calculated in writing,that's way the car start,but you will lost the synchro of cks between the blocs in the chip
learn more about this,
and for your information,the most difficult ecu that i had chiptuning,have more than 1400maps,and i did it with succes:D

You will loose nothing, MPPS will calculate checksum while writing and that's all. You can flash by OBD, and then read by BDM to check- and you will have same result. As always you have no idea what you are talking about.

[coolis]

Can someone recomented me good cable via PM (v5 or newest), I want?to read bmw edc16c35.

My v3 .37 version don?t want to read right. Excample Car vin number looks like this "&//%"#"""## l

[lulu2003]

that's normal.

[blacktoy]

Hi,

I have a problem with writing a EDC16 CP34.

Are there any known issues?

br

[masterb]

Hi,

I have a problem with writing a EDC16 CP34.

Are there any known issues?

br

which problem ... stop write ...

[coolis]

that's normal.
It?s normally file size 1024kb, BMW EDC16c35 ?

[psico]

It?s normally file size 1024kb, BMW EDC16c35 ?

yes , is correct, mpps only read 1.024mb , and no problems, you write 1.024.

[258]

read MPPS EDC16C31 BMW 2.0 TDI 150 cv, check whether read?.

[258]

how to update Mpps v5 clone to v10?

[J_amb_o]

You don't want to do that

[lolooo1981]

how to update Mpps v5 clone to v10?

You need to change MCU.
But if you have only one interface, i think you would have stay in V5 because in V10 nothing new....

Regards

[258]

V5 does not read correctly EDC16C31, so ask about V10

[bazare]

i can proove you are wrong, and edc16c31 is good read by mpps

[maglaras]

where can i found mcu v5 for me mpps??
i tray to make it v5 and noe the cable did not work
can you help me to found mcu
i put the cable on the laptop and i dont show power 12v
i must take a new one or take only mcu???
thank you

[daniel guerra]

where can i found mcu v5 for me mpps??
i tray to make it v5 and noe the cable did not work
can you help me to found mcu
i put the cable on the laptop and i dont show power 12v
i must take a new one or take only mcu???
thank you

I think in order to have 12v you need to connect it to a car, if you plug only the cable on the computer you need to have the version of the cable instead of error.

[TOSHIBA1]

Hallo
wo kann man die beste Software f?r Mpps Flasher Clone downloaden???

[Nio]

Only english language. Read rules please.

[bazare]

This is english forum ...

[maglaras]

i put it on the car and i dont show power 12v
i show eeror1??
what is this??
thank you

[lolooo1981]

i put it on the car and i dont show power 12v
i show eeror1??
what is this??
thank you

I think dead clone.

Regards

[maglaras]

i think if i put i new on mcu
or if i rite the same mcu v5 my cable is work again

[obnchip]

How come mpps read from bosch me7.5 29f400 1mb dump?The file is doubled thats why its 1mb 512*2...

[yellowstilo]

MPPS V12 is out, it is nessesary to send the (original) tool to AMT Cartech for this upgrade so i guess they invented another clone killing trick....

AMT Cartech Limited - The origin of flash tuning (http://www.amtcartech.com/content.jsp?pname=Home)

[258]

i can proove you are wrong, and edc16c31 is good read by mpps

You're right reads, but can not find VinOls checksum file attached in the post above from the BMW e 46 150 cv. You can check if it is correctly read.

[Dobermann]

Hello Dobermann,

chips received today and finally got my MPPS V8/9/10 working !

thanks again for your help !!

hello yellowstilo

sorry for the long time to answer !!!

thats great that your MPPS is now working !!!

ok now is V12 out !! I installed it today !! i will test it later on my car me7.5

the problem is now installing V12 no problem !! but the MPPS software can only be run 128 times before updating the hardware !!

there is a counter inside and count down the starts of the soft !!

i have clone and genuwine tool !!

i musst send my genuwine tool to amt i think they want change something in the interface !!

King Regards

[blacktoy]

does anyone has an idea on how to deactivate the 128 times restriction?

what changes will AMT Cartech perform to the interface?

[lolooo1981]

MPPS V12 is out, it is nessesary to send the (original) tool to AMT Cartech for this upgrade so i guess they invented another clone killing trick....

AMT Cartech Limited - The origin of flash tuning (http://www.amtcartech.com/content.jsp?pname=Home)

It was sure.
This is the only one solution for Amt Cartech to kill last clone but until when ?new clone ?
I hope Amt Cartech will add new protocols...

Best regards

[lolooo1981]

does anyone has an idea on how to deactivate the 128 times restriction?

what changes will AMT Cartech perform to the interface?

Apparently problem with some Ecu we're done.
We will see...

regards

[elchip]

Did someone updated to V12 ?
I was today and nothing new as they say on manufacturer website , no new ecu nothing...

Only one is new hehehehe they added counter in new firmware from 128 to 0 for every start of PC application and if you want to fix that you must write all your personal data etc to they FORM downloaded from official website to they give you way to go forward with application ...
So another version to stop clones ....

I am sick from MPPS ...

I was back after test to V10 working with original SW.
I think that I live as is.... I cant re flashing my tool every time when they put new version on they website.

Regard's

[lolooo1981]

H?h?.That's a good solution :D


Did someone updated to V12 ?
I was today and nothing new as they say on manufacturer website , no new ecu nothing...

Only one is new hehehehe they added counter in new firmware from 128 to 0 for every start of PC application and if you want to fix that you must write all your personal data etc to they FORM downloaded from official website to they give you way to go forward with application ...
So another version to stop clones ....

I am sick from MPPS ...

I was back after test to V10 working with original SW.
I think that I live as is.... I cant re flashing my tool every time when they put new version on they website.

Regard's

[lulu2003]

it seem they are doing one error after the other.
of course it can make sense to have a send-in and new-hardware strategy but only with new features for the genuines...

[maglaras]

it seem they are doing one error after the other.
of course it can make sense to have a send-in and new-hardware strategy but only with new features for the genuines...

well i tray to make me clone version 5
and i now that it can be that to broke my clone
DOU YOU NOW HOW CAN I MAKE IT WORK AGAIN
i ame here to help not to laugh at the problems of others
***932;***919;***913;***925;***922; YOU
IF I CAN???????????????????????:beheaded:

[elchip]

it seem they are doing one error after the other.
of course it can make sense to have a send-in and new-hardware strategy but only with new features for the genuines...

Yes it is no problem for me to I reprogram my MPPS and use any original SW from V5 up to V10 .....

But I dont have a time to play with they game for KID's ..

As I see all go in wrong way ....
No one as they on market do a fight with clones or extra copy's 1:1 which peoples make and from my experience that way not go in good direction ...

Many bigger Company's cant fight with copying they work so ....

Sorry if I disturb someone but I just need to comment that stupid update from V10 to V12...

Simple is if I want to use V12 I only reflash to V10 after 128 start's of PC application and go again again again ...

I dont use it every day so its no problem ...

If you add all time and money which you spend for that game better is buy Original Galletto for 3000E and have extra tool ...

So is they way is good ? I think no and " THAY PLAY WITH CUSTOMER IN THAY EXPERIMENT " ....