VW Touran - Adapting used ECU

[bidu20]

Hi,

I need your help. On VW Touran 2007.

My old ECU is broken. Completely burned. i can't read immo data anymore. No communication.

I have PIN, Immo ID, CS from used ECU. I have PIN and CS from the dashboard (same as old ECU). But i can't adapt the used ECU on the car. I try with VCDS, SMOK or CARPROG, doesn't work. Can someone help me ?

ECU Bosch 03C 906 032C / 0 261 201 538
Dash VDO 1T0 920 873 D

Can someone help me ? How can I adapt without ODIS ?

Thanks

[rafal]

make immo off and don't bother with this old car

[kiszka]

Hi,

I need your help. On VW Touran 2007.

My old ECU is broken. Completely burned. i can't read immo data anymore. No communication.

I have PIN, Immo ID, CS from used ECU. I have PIN and CS from the dashboard (same as old ECU). But i can't adapt the used ECU on the car. I try with VCDS, SMOK or CARPROG, doesn't work. Can someone help me ?

ECU Bosch 03C 906 032C / 0 261 201 538
Dash VDO 1T0 920 873 D

Can someone help me ? How can I adapt without ODIS ?

Thanks

send component security read carprog from dash and eeprom data from ecu

[bidu20]

here ...........

[rafal]

here ...........

open eeprom...................which you posted - come back when ready
better post full back up

[lupu_sandu]

You need to post external flash and internal MCU flash from ECU.
Eeprom will not help you on this case.

[bidu20]

I don't know why but is always 000000 in eeprom. I read eeprom, flash and processor. The processor is good read ... but the eeprom always empty ...

[rafal]

ecu bad readed................. size is wrong

[bidu20]

Flash 4096kb, Processor 2048kb, Eeprom 128kb, i think is correct. i check with other files on the forum, is the same size !

[kiszka]

Flash 4096kb, Processor 2048kb, Eeprom 128kb, i think is correct. i check with other files on the forum, is the same size !

the problem is that you want to connect immo 4 with immo 5 not possible in my opinion
this year it was edc16c34
compenent, the dash is ok

[lupu_sandu]

There in no immo5 on this ecu mate.

[rafal]

Flash 4096kb, Processor 2048kb, Eeprom 128kb, i think is correct. i check with other files on the forum, is the same size !

you are wrong m8
when i said is bad so is bad..................
flash should have 6 mb sticked together with emulated eeprom ( reason why your eeprom always full 000000000 )
i don't care what others users posted as you said
for off , egr or tuning etc ..............ok 4mb enough
in your case need 6mb
but if you want to be smart - do by self
here from med17.5.1 readed correctly:


the problem is that you want to connect immo 4 with immo 5 not possible in my opinion
this year it was edc16c34
compenent, the dash is ok
you wrong


There in no immo5 on this ecu mate.

that is correct answer

[redaveliem]

try reading again you have bad file size

[kiszka]

There in no immo5 on this ecu mate.

Then if it's not immo 5 then why doesn't it allow reading
I hope this ecu has 8 bit CS because if 16 bit, let him forget about synchro only immo off
I hope the Can gateway can handle this ecu

[kuebk]

IMMO OFF in external flash.
Or post immo data in human readable format if you want to adapt this ECU.

[bidu20]

i can't open the immo off file .. immo off is the best solution, can someone do immo off on my file ? If possible, without "Immo active" displayed on the dash .. ! Thanks a lot

[lupu_sandu]

I don't know what you all smoke, but this is not good for your health.
ECU it's readed ok, immo is in flash and can be decrypted without problem.

Details:

VIN: WVGZZZ1TZ7W019651
CS: DFED599BBFDA
PIN: 62109
MAC: 953D51ED

[bidu20]

Thanks mate, the car starts again !