Audi A8 4.2/v5 D2 need sw after crash.

[306 t16]

Hi All,

Can somebody please help with right sw.

after read with Kess ecu is dead, wrote have OF the file.

I think i have found good flash file 1mb.
i think eprom is in boot mode or something.
also read eprom before flashing with avdi.
still no communication with rest of car.

ME7.1.1
4D0907558AC
0261207629
1037362911

somebody can check eprom dump??

[kiszka]

Hi All,

Can somebody please help with right sw.

after read with Kess ecu is dead, wrote have OF the file.

I think i have found good flash file 1mb.
i think eprom is in boot mode or something.
also read eprom before flashing with avdi.
still no communication with rest of car.

ME7.1.1
4D0907558AC
0261207629
1037362911

somebody can check eprom dump??
where did you lost your files

[306 t16]

KESS READ AS 29F400 AND IS 29F800 , ALSO WRITE FILE AS 29F400.
FOUND OTHER FILE ON FORUM, BUT I THINK EPROM IS LOCKED????
ALSO READ EPROM WITH AVDI BEFORE USED KESS AND WRITE THAT FILE BUT NO LUCK....

[kiszka]

KESS READ AS 29F400 AND IS 29F800 , ALSO WRITE FILE AS 29F400.
FOUND OTHER FILE ON FORUM, BUT I THINK EPROM IS LOCKED????
ALSO READ EPROM WITH AVDI BEFORE USED KESS AND WRITE THAT FILE BUT NO LUCK....
show the flash you read
this eeprom reading is scrap, only the necessary data can be taken from it if they are true
write here without using caps lock
pin is 00176

[306 t16]

in attachment ori read and flash file i get from internet.

when i write eprom file 5p08c3 with avdi , i can read ecu on bench and all looks oke.

after i put ecu in car there is no communication with other ecu or scantool, and when read on bench eprom looks different and lost software.

[kiszka]

in attachment ori read and flash file i get from internet.

when i write eprom file 5p08c3 with avdi , i can read ecu on bench and all looks oke.

after i put ecu in car there is no communication with other ecu or scantool, and when read on bench eprom looks different and lost software.
writing this eeprom with AVDI you did the biggest stupid thing you could do
unstick the ecu, read with the eeprom programmer and send me the read eeprom, or insert it here

[306 t16]

i read eprom as 95040

[kiszka]

i read eprom as 95040
at first glance, the eeprom looks good, so what is changing in your opinion
only the eeprom is not full read

[306 t16]

well the car wont start and there is no communication after install ecu in car. before i test on bench there is no problem to read ecu.

after install in car , even bench read wont work , eprom is missing some data.

attachment is read after install ecu in car.

[kiszka]

well the car wont start and there is no communication after install ecu in car. before i test on bench there is no problem to read ecu.

after install in car , even bench read wont work , eprom is missing some data.

attachment is read after install ecu in car.
this reading is programmer whether after OBD AVDI

[306 t16]

yes is avdi, but other programmer is the same.

[kiszka]

yes is avdi, but other programmer is the same.
don't use that AVDI shit, to write eeprom
write with eeprom programmer and mount to ecu
but use a programmer that will save as 95p08, do not save eeprom as 95040 because you are doing stupid things
if you can't afford a better one, buy this programmer
It's not a miracle of technology, but it works well
http://www.xgecu.com/en/

[306 t16]

you are right Sir, i have xgucu and also Elnec BeeProg. when i use 5P05c3 i can see something is missing in the last few sectors. Tommorow i will try to find missing data.
Thanks for help, really appreciate!

[kiszka]

you are right Sir, i have xgucu and also Elnec BeeProg. when i use 5P05c3 i can see something is missing in the last few sectors. Tommorow i will try to find missing data.
Thanks for help, really appreciate!
To have such equipment, you use such AVDI shit to write eeprom, is it laziness, then you have symptoms of this laziness, Ecu broken
I hope you can deal with it now, if not, write me and I will try to help as much as possible from a distance