Astra H gtc airbag crash

[carclima]

can anybody check this temic 13 251 079 modul,car have small accident with only one aibag deployed..now have 5 erors one of them is crash..I read 95160 and try to repair it with sw.donloaded somewhere..now I have 7 erors one of them is memory full ??so can anybody check myne dump and repair it..car is still with me so I can check it ..

[juozas10]

can anybody check this temic 13 251 079 modul,car have small accident with only one aibag deployed..now have 5 erors one of them is crash..I read 95160 and try to repair it with sw.donloaded somewhere..now I have 7 erors one of them is memory full ??so can anybody check myne dump and repair it..car is still with me so I can check it ..

Hi.
Try this crash data cleared 100%.
Write back if it works.

Best regards.:wink:

[carclima]

Hi.
Try this crash data cleared 100%.
Write back if it works.

Best regards.:wink:

Hello ! well my friend youre file is OK..all work fine..no faults on diagnostic..

thank you once again!

[Ashraf6119]

Hi

Why you want crash data cleared :questionmark:

On Astra H if the Vehicle is involved in an Accident and if all the Damaged Airbags and Pretension are replaced as it should be the Crash Data will be cleared by it self.

And that all can be reset by using Op-Com or Vaux-Com.

The procedure is as follow:

1) First you should make sure that All the Damaged Airbag system parts are replaced and All the work is carried out as it should be.

2) Log-in to Airbag module and read the fault codes note them down.

3) Select Activation option and select all component that show in your fault codes and activate them.

4) Log-off from the Airbag system and disconnect your diagnostic tool.

5) Lock the Vehicle using your remote fob and wait for few min unlock the Vehicle using your remote fob.

6) Log-in Again in to Airbag system and Clear all fault codes and log-off.

7) Disconnect the Battery for few min and reconnect it again.


If all your Airbag system work is been carried out properly your Airbag light should go Off now.

BEFORE YOU CARRY OUT THIS PROCEDURE LOOK IN THE FOLLOWING WEB SITE

For more info look in Op-Com wiki site....

And if you are not sure what to do than please don't do its entire your own risk


Ash

[carclima]

Hi

Why you want crash data cleared :questionmark:

On Astra H if the Vehicle is involved in an Accident and if all the Damaged Airbags and Pretension are replaced as it should be the Crash Data will be cleared by it self.

And that all can be reset by using Op-Com or Vaux-Com.

The procedure is as follow:

1) First you should make sure that All the Damaged Airbag system parts are replaced and All the work is carried out as it should be.

2) Log-in to Airbag module and read the fault codes note them down.

3) Select Activation option and select all component that show in your fault codes and activate them.

4) Log-off from the Airbag system and disconnect your diagnostic tool.

5) Lock the Vehicle using your remote fob and wait for few min unlock the Vehicle using your remote fob.

6) Log-in Again in to Airbag system and Clear all fault codes and log-off.

7) Disconnect the Battery for few min and reconnect it again.


If all your Airbag system work is been carried out properly your Airbag light should go Off now.

BEFORE YOU CARRY OUT THIS PROCEDURE LOOK IN THE FOLLOWING WEB SITE

For more info look in Op-Com wiki site....

And if you are not sure what to do than please don't do its entire your own risk


Ash

there was small carcrash on driver door and only this bag (in driver seat) was engaged and pretensioner for belt..I replace this two component and have 5 erors in airbag ecu (read with kts540) ..my opcom CANT acess to this airbag system,,not even log in..so all my work is based on kts..but kts cant erase crash or any eror IF there is crash stored..after clearing this dump I was able to disconect driver bag (on stering whell) read erors and clear this eror with kts..so kts work fine IF there is NO CRASH code stored..

and of corse my opcom is some chines version..but who have original???

also Brain bee and texa can clear this code..only kts cant.even it is relativly new 2009/4 kts 540..so this solution via dump change is my only way to make this yob done and earn some money..

regards and thanks for youre effort in explanation how opcom work


hmmm in youre description there is option delete erors only on 6-th step...soooo in this way maybe even bosh can clear the codes..interesting procedure I will save it for future use..thanks

[FlaviusBFG]

Hi.
Try this crash data cleared 100%.
Write back if it works.

Best regards.:wink:


WORK ! VERY GOOD !!! Thanks ;) :captain: