View Full Version : almera 02 Correction
justy22
31st March, 2010, 12:23 AM
Hi all
whats the best way to do correction on my almera 02 plate with tacho universal, what order do i connect my sw13 cable to the board
all help appreciated please
GolfmkI
31st March, 2010, 12:33 AM
But this car has not 93c66 inside????
I have Tacho universal and I am looking for and no one is sw13 cable????
madzar
31st March, 2010, 01:11 AM
KM is stored in memory 93c66
The mileage is stored in the next lines:
0060: xx xx xx xx xx xx xx xx AF 27 5E 4F BC 9E 79 3D
0070: xx xx 5E 4D BC 9A xx xx xx xx xx xx xx xx xx xx
where the next bytes:
String #1 = AF 27 5E 4F BC 9E 79 3D
String #2 = 5E 4D BC 9A
GolfmkI
31st March, 2010, 01:24 AM
Correct, I was thinking I was the only one have this info.
justy22
31st March, 2010, 01:26 AM
KM is stored in memory 93c66
The mileage is stored in the next lines:
0060: xx xx xx xx xx xx xx xx AF 27 5E 4F BC 9E 79 3D
0070: xx xx 5E 4D BC 9A xx xx xx xx xx xx xx xx xx xx
where the next bytes:
String #1 = AF 27 5E 4F BC 9E 79 3D
String #2 = 5E 4D BC 9A
Can i use tacho universal to change it
GolfmkI
31st March, 2010, 01:38 AM
Of course you can.
..... Open the dash
......Look for the christal and join its contacts
......use adaptor with smd clip.........
I upload the nissan pdf that I have, could be usefull for you.
justy22
31st March, 2010, 01:44 AM
Of course you can.
..... Open the dash
......Look for the christal and join its contacts
......use adaptor with smd clip.........
I upload the nissan pdf that I have, could be usefull for you.
Thanks Buddy
justy22
31st March, 2010, 10:31 AM
just tried via clip and cant do it, how do i use the points on the back of the cluster
florinyes
31st March, 2010, 10:53 AM
Desolder the eeprom. Much more reliable.
justy22
31st March, 2010, 11:14 AM
Desolder the eeprom. Much more reliable.
im not confident enough to desolder it can you show me the how to connect to the test points on the board, when i try the clip it comes back data un equal
florinyes
31st March, 2010, 12:28 PM
Mate just download manual from post 6. Join crystal, grab with clip as per picture read eeprom modify and then program...
Easy job on that one.
Have you got air station?
justy22
31st March, 2010, 01:03 PM
Mate just download manual from post 6. Join crystal, grab with clip as per picture read eeprom modify and then program...
Easy job on that one.
Have you got air station?
My clip is not working, can anybody give me details to solder the wire direct to the board
florinyes
31st March, 2010, 01:38 PM
You can easy fix your clip mate. First test it with a ohm meter. If not good problem is by the plug. Just open up the connector (carefully) cut the cable straight so you get rid of the end bit and crimp it back on a vice..
justy22
31st March, 2010, 02:04 PM
Done it via clip, But why did it come back data unequal adjust click when in fact it had worked
Thanks everybody for all ur help
florinyes
31st March, 2010, 02:21 PM
That is normal mate. Chinese stuff I suppose...
justy22
31st March, 2010, 03:07 PM
That is normal mate. Chinese stuff I suppose...
What is'nt chinese these days, low cost and does the job
ALEXEI
1st April, 2010, 09:33 PM
Done it via clip, But why did it come back data unequal adjust click when in fact it had worked
Thanks everybody for all ur help
ALLWAYS DESOLDER THE MICRO ON ALMERA AND ALSO IN OTHER NISSAN WITH C66 IS IMPORTAND IF YOU WANT TO BE IN RIGHT WAY USING CHINNES TOOL:beer:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.